Wiring Options For Controlling Laminar Jet With Led Lights; Wiring To A Time Clock; Wiring To A Switch - Jandy JLLED4C Serie Manual De Instalación Y Operación

Page 10 ENGLISH
120 VAC
Power Supply
Black
White
Neutral
Green
Ground
Figure 7. 12-Volt Laminar Jet with LED Light
Wiring Diagram
A 1
Neutral
Line
Ground
Ground
Figure 8. Wiring the Laminar Jet with LED Light
to a Time Clock
SWITCH
Neutral
Line
Ground
Figure 9. Wiring the Laminar Jet with LED Light
to a Switch
Jandy Laminar Jet | Installation and Operation Manual
®
Laminar Jet
with
LED Light
Black Black
White
White
120V/12V JUNCTION
Transformer*
BOX
Green
Green
*Transformer must be supplied by a GFCI if required
by the transformer manufacturer's instructions, or by
local code and AHJ requirements
Laminar Jet
with
LED Light
Clock
Motor
2
Black
Black
JUNCTION
120V/12V White
White
Transformer* BOX
Green
Green
*Transformer must be supplied by a GFCI if required
by the transformer manufacturer's instructions, or by
local code and AHJ requirements
Laminar Jet
with
LED Light
Black Black
JUNCTION
120V/12V
White
White
BOX
Transformer*
Green
Green
*Transformer must be supplied by a GFCI if required
by the transformer manufacturer's instructions, or by
local code and AHJ requirements
4.3 Wiring Options for Controlling
Laminar Jet with LED Lights
NOTE: The laminar jet with LED lights will not operate
properly with light dimmers. Do not wire the
laminar jet with LED lights to any dimming
circuitry.
To the extent allowed by code and capacity of the To the extent allowed by code and capacity of the
electrical equipment, multiple laminar jets with LED electrical equipment, multiple laminar jets with LED
lights may be controlled with a single switch so their lights may be controlled with a single switch so their
colors will always colors will always be synchronized. be synchronized.
Separate switches may be used to control the on/off Separate switches may be used to control the on/off
and color functions of each laminar jet with LED light. and color functions of each laminar jet with LED light.
It is recommended that these switches be located next It is recommended that these switches be located next
to each other to facilitate simple color synchronization to each other to facilitate simple color synchronization
when desired. All switches must be operated at the same when desired. All switches must be operated at the same
time to assure color synchronization time to assure color synchronization. . Otherwise, the
lights will work independently of each other. lights will work independently of each other.
4.3.1 Wiring to an AquaLink
Control System
The laminar jet with LED light can be wired into
the Jandy AquaLink RS control system to provide
simplified operation of the lights, as well as a means
to synchronize the color change function. Connect the
laminar jet with LED lights to one of the auxiliary relays
in the Power Center.
NOTE: It is recommended to connect one (1) laminar
jet with LED light per relay so each light can be
controlled separately. However, up to four (4)
laminar jets with LED lights can be connected
on a single relay. If there are more than four (4)
lights installed on one (1) AquaLink RS system,
ensure there is more than one (1) auxiliary relay
available in the Power Center.
Connect the laminar jet with LED lights to the power
center.
NOTE: The laminar jet with LED light operates only
on 12 volts AC. A suitable 120-volt/12-volt
stepdown AC transformer MUST be used.
Read further for more important details.

4.3.2 Wiring to a Time Clock

The laminar jet with LED lights can be wired into a
basic time clock to automatically turn on the laminar jet
with LED lights at a predesignated time. Connect the
laminar jet with LED lights into the time clock.

4.3.3 Wiring to a Switch

The laminar jet with LED lights can be wired into a
switch to manually turn on/off the lights. Connect the
laminar jet with LED lights into the switch.
Otherwise, the
RS
®