Descargar
Compartir
Imprimir esta página
  1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Receptores para Coches
  5. 99-7526B
  6. Instrucciones de instalación

Metra 99-7526B Instrucciones De Instalación

Ocultar thumbs
1
2
3
4
5
6
7
8

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
KIT COMPONENTS
• A) Radio trim panel (a) • B) Radio trim panel (b) • C) Radio housing base• D) Radio brackets • E) Radio support bracket • F) (4) Panel clips
• G) (2) #8 x 1/2" Phillips screws
A
B
Metra. The World's Best Kits.
®
Mazda 3 2014-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted matte black
C
F
MetraOnline.com
D
E
G
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
99-7526B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Preparation . ......................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: 70-7903L (without amp)
Antenna Adapter: 40-HD10L
Steering wheel control interface: ASWC-1 & AX-
MAZ28SWC-6V (will also retain backup camera)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 10mm Socket wrench • 1/8" drill bit
Attention!
With the key out of the ignition,
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
REV. 4/18/22 INST99-7526B

Publicidad

loading

Manuales relacionados para Metra 99-7526B

Resumen de contenidos para Metra 99-7526B

  • Página 1 Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/18/22 INST99-7526B...

  • Página 2: Dash Disassembly

    DASH DISASSEMBLY KIT PREPARATION 1. Unclip and remove the dashboard trim 1. Secure the radio support bracket to panel above the glovebox. This panel the sub-dash using the factory 10mm will also include the middle a/c vents. screw removed in dash disassembly. (Figure A) Directly above this is the factory radio support brace. Bend this towards the 2. Remove (1) 10mm screw securing the front of the vehicle to allow room for the radio, then unclip, unplug, and remove aftermarket radio. (Figure A) the radio. (Figure B) 2. Remove the panel clips from the factory (Figure A) radio, then attach them onto the radio Continue to Kit Preparation housing base. (Figure B) 3. Clip the radio housing base to the dash. (Figure A) (Figure C) Continue to Kit Assembly (Figure B) (Figure B) (Figure C) 386.257.1187 MetraOnline.com...

  • Página 3: Kit Assembly

    2. Remove the metal DIN sleeve and trim be drilled into the sub-dash. Either drive ring from the aftermarket radio. the screws in, or pre-drill the holes with 3. Attach the radio brackets to the radio a 1/8” drill bit. using the screws supplied with the 6. Attach radio trim panel (a) to the radio. (Figure B) assembly. 4. Locate the factory wiring harness and 7. Starting from the bottom, attach radio antenna connector in the dash and trim panel (b) to the assembly. complete all necessary connections to (Figure A) the radio. Metra recommends using 8. Reassemble the dash in reverse order of the proper mating adapter from Metra disassembly to complete the installation. and/or Axxess. Test the radio for proper operation. Note: The wiring harness and antenna connector are located in the passenger kick panel, except for the 2014 i-Sport. (Figure B) REV. 4/18/2022 INST99-7526B...
  • Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/18/22 INST99-7526B...
  • Página 5 Al probar el equipo del mercado de accesorios, asegúrese de que todo el equipo de fábrica esté conectado antes de encender el llave de encendido. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/18/22 INST99-7526B...

  • Página 6: Desmontaje Del Tablero

    DESMONTAJE DEL TABLERO PREPARACIÓN DEL KIT 1. Desenganche y quite el panel de 1. Fije el gancho de soporte del radio al moldura del tablero que está arriba sub-tablero usando el tornillo de fábrica de la guantera. Este panel también de 10 mm que se quitó...

  • Página 7: Ensamble Del Kit

    8. Vuelva a ensamblar el tablero en el necesarias al radio. Metra recomienda orden inverso al desensamble para el uso de adaptadores de acoplamiento adecuados de Metra o de Axxess. Pruebe terminar la instalación. el radio para asegurarse de que funciona bien.
  • Página 8 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recomienda MECP técnicos certificados Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/18/22 INST99-7526B...