Dustbin Assembly - Roborock Q7 Max+ Manual Del Usuario

Mop Cloth
A13
A13-1—Mop Cloth
A13-2—Hook and Loop Pads
Screwdriver
A14
Power Cable
A15
Installation
B
Important Information
B1
B1-1—Tidy cables and loose items from
the ground and move any unstable,
fragile, precious, or dangerous
items to prevent personal injury
or property damage due to items
becoming tangled in, struck by, or
knocked over by the robot.
B1-2—When using the robot in a raised
area, always use a secure physical
barrier to prevent accidental falls
that may result in personal injury or
property damage.
Note: When using the robot for the first time, follow
it throughout its whole cleaning route and watch for
potential problems. The robot will be able to clean by
itself in future uses.

Dustbin Assembly

B2
B2-1—Take the screwdriver from its storage
bin at the bottom of the base.
B2-2—Place dock upside down on a soft,
flat surface (carpet/towel/cloth) and
attach the base by using the six
screws provided.
Note: Hold the dustbin cover securely when upside
down to prevent damage from falling.
B2-3—Connect the power cable to the dock,
and keep the excess cable inside the
storage slot.
B2-4—Place the dock on a hard and flat floor
(wood/tile/concrete etc.). Keep at least
0.5 m (1.6 ft) of clearance on either
side, 1.5 m (4.9 ft) in front, and 1 m
(3.3 ft) above. Check the location has
good WiFi then turn on.
B2-4-1 More than 0.5m (1.6 ft)
B2-4-2 More than 1.5m (4.9 ft)
B2-4-3 More than 1m (3.3 ft)
Emptying
B3
Auto-emptying will begin when the robot
returns to the dock after cleaning. Press
the button to trigger emptying manually.
Press any button to stop emptying.
Notes:
• The status indicator light turns off automatically when
the robot is charging.
• Do not use without dustbin cover or dust bag.
• Place the dock on a flat floor away from fire, heat, and
water. Avoid narrow spaces or locations where the
robot may be suspended in the air.
• Placing the dock on a soft surface (carpet/mat) may
cause the dock to tilt over and cause problems
docking and departing.
• Keep the excess power cable inside the storage slot so
that the robot will not get tangled in the cable, and the
06
dock will not be dragged away or disconnect from the
power supply.
• Keep the dock away from direct sunlight or anything
that may block the dock location beacon; otherwise,
the robot may fail to return to the dock.
• The Auto-Empty Dock recharges and empties. Store
the standard robot dock before use. Failure to do so
may cause issues returning to dock.
• Maintain the dock according to the maintenance
instructions. Do not clean the dock with a wet cloth.
• Avoid frequent manual emptying.
• Images are for illustration purposes only and may not
exactly represent the product.
Mopping
B4
Note:
To prevent excessive dirt buildup during first-time
use, floors should be vacuumed at least three times
before mopping.
B4-1—Remove the dustbin and water
tank combo unit
Open the upper cover and take out the unit.
B4-2—Fill the water tank
Remove the water tank stopper, fill the tank
with water, and close it tightly.
Notes:
• To prevent corrosion or damage, only use the
Roborock branded floor cleaner in the water tank.
• Do not use hot water as this may cause the tank to deform.
• When filling the water tank, tilt tank 30° to avoid
wetting the filter.
B4-3—Reinstall the dustbin and water
tank combo unit
Reinstall the unit. It will click in place.
B4-4—Install the mop cloth
Wet the mop cloth and wring it until it stops
dripping, then slide it along the mop cloth
slot before sticking it firmly in place.