GN Netcom GN 9000 Serie Manual Del Usuario página 2

Thank you for purchasing a GN Netcom product.
All GN Netcom products are designed and manufactured in accordance with strict quality standards and should,
with a minimum of maintenance, give many years of satisfactory use.
GN Netcom A/S
This user guide includes the following 9 languages: UK, D, F, E, I, NL, DK, S and SF.
© GN Netcom A/S. All rights reserved.
The information in this user guide is furnished for informational use only, is subject to change without notice, and
should not be construed as a commitment by GN Netcom. GN Netcom assumes no responsibility or liability for any
errors or inaccuracies that may appear in this user guide.
Written and designed at GN Netcom A/S, Metalbuen 66, DK-2750 Ballerup, Denmark.
2
GN_9020_contents_4_new.indd 2-3
English
To see the illustrations, fi rst unfold the back cover.
Assembling the GN 9000
Disconnect handset cord from telephone and connect it to socket marked 0 at the bottom of base unit (A).
1.
Connect cord with modular plug (D) to the handset socket on the telephone and to socket marked 1 at the
bottom of the base unit. Connect power unit adapter (C) to socket marked 2 at the bottom of base unit, and
then to a power socket. Switch on power.
Note: If you plug the modular cord (D) into the telephone's headset port, this will enable the line button on
the telephone. However, if you have a GN Netcom Hook Switch for remote handset lifting, the cord must be
plugged into the handset port for the Hook Switch to work.
2. Mount base unit on stand (B) by turning clockwise until secure. The three cords can extend from the front or
back of the base unit as you wish.
3. Insert headset into base unit. Both sides of base unit can be used. The battery charging indicator (V) on base
unit will light up. This side will be referred to as the front of the base unit.
Before setting up the GN 9000 to your telephone
4. The battery in the headset is not charged when delivered. To start, place the headset in the base unit for at
least 45 minutes before making the adjustments below. It takes 1½ hours to fully charge the battery of a GN
9000 - Bluetooth™ headset, and 3 hours to fully charge the battery of a GN 9000 Digital.
Note: If your telephone has volume control, set the volume in the middle position.
Checking the system
5. Remove the headset from the base unit. The link will be instantly established and the on-line indicator (IV) on
the front of the base unit will light up. If the on-line indicator does not light up, please switch on the headset
connection by pressing the headset/handset button (I) on top of the base unit (press gently until it clicks).
0-10 seconds after having removed the headset from the base unit, the on-line indicator (VIII) on the headset
starts fl ashing. If the on-line indicator on the headset does not fl ash, please place the headset in the base unit
again and remove it from the base unit once more.
The system is now working.
Make sure that the mute function is off. If the mute function is on, you will hear a beep every 15 seconds in
your headset (see Technical Data). Turn off the mute function by pressing the multifunction button (VI) on the
headset once.
Setting up the GN 9000 to your telephone
Adjusting GN 9000 to your telephone
6. Put on your headset.
7. Lift handset from telephone (or if available on your telephone press the line button) and listen for a dial tone in
your headset.
8. If there is no clear dial tone, adjust the telephone termination switch (III) at the rear of the base unit. Move from
A to G until the dial tone is clear. If the dial tone is just as clear in position A as in position G, then leave the
switch in position A.
Adjusting the microphone volume
9. Change from headset to handset position by pressing the headset/handset button on top of the base unit once.
10. Put on your headset, lift the handset from telephone (or if available on your telephone, press the line button)
and listen for a dial tone in your headset. Call someone and ask the person to help you evaluate the volume of
your voice.
11. Adjust the microphone volume control (II) from 1 to 8 by talking in the headset in each position. When the
person you are talking to fi nds the sound level good, you have the correct setting. If the best setting is 7 or 8,
you may have to move the telephone termination switch (III, from A-G) to G.
3
31-05-2002, 10:33:19