Publicidad
Idiomas disponibles
Idiomas disponibles
performed by personnel without technical expertise or complex
equipment. It involves above all:
Check the level of oil in the pump by means of the
indicator on the pump itself.
Clean the connectors and grease the connector gaskets
IMPORTANT - When replacing oil, it must be disposed
of in respect of current legislation. Under no
circumstances may it be disposed of in the
environment.
8.2
Safety regulations for cleaning the machine
All cleaning operations must be performed with the machine
stationary and turned off. When cleaning the machine or its
components, the following precautions must be observed:
Do not clean electrical equipment with water or other fluids. To
remove dust, use a clean brush or dry cloth only. Do not clean
plastic surfaces with alcohol, detergent or solvents. Dispose of
cleaning materials in respect of current legislation. Do not dispose of
the materials used or cleaning residues in the environment. To
clean, use water or compressed air and soft cloths. IMPORTANT -
During cleaning, personnel protection devices must be worn
8.3
Safety regulations for repairs and
extraordinary maintenance
For all operations over and above normal routine maintenance,
contact an authorised repair workshop.
All operations must be performed by qualified
personnel with the necessary technical skills to
perform the operations in the maximum safety and in
respect of current legislation.
It should be noted that the warranty offered by the manufacturer is
invalidated if:
The instructions given in the "use and maintenance"
manual are not scrupulously respected,
Routine maintenance is not performed as and when
indicated;
Lubricants other than those specified are used;
Repairs or maintenance are performed by unqualified
personnel;
Non-original spare parts are used;
Unsuitable tools are used.
IMPORTANT - The customer is responsible for
verifying that original parts only are used when
carrying out repairs. The use of non-original spare
parts could jeopardise the safety of the machine.
When ordering spare parts, specify the model and serial number of
the machine and the reference number of the component in the
spare parts book and quantity.
9
Storing the machine
9.1
Storing the machine
If the machine is not used for long periods, protect exposed parts
(not protected by paint, surface treatment or plastic) with protective
rust prevention oils. If the machine is not to be used for particularly
long periods, you should also clean it thoroughly. After performing
these operations, seal the machine inside an opaque black
multilayer nylon bag together with a suitable drying agent (silica gel).
10
Disposal
10.1
Disposing of the machine
At the end of its working life, the machine must be scrapped and
disposed of by taking it to a local differentiated waste collection
centre in compliance with current legislation which must be followed
scrupulously. Before disposing of the machine, check the machine
rating plate. If it bears the
regulated by EC directive 2002/96 on Waste Electrical and
Electronic
Equipment,
WAEE.
information on the local electrical and electronic products collection
system and follow the instructions. Disposing of this product illegally
in the household waste could cause serious damage to the
environment and human health and you may be liable to sanctions
from the local authority.
11
Table of regular maintenance
OPERATION
Check the functioning of all
controls
Check connector gaskets
Check oil level in the pump
12
Troubleshooting
The table below gives the most common problems which may arise
during normal use of the high pressure washer. These problems are
easy to resolve with operations classified as routine maintenance If
the problem is not present in the following table or cannot be
eliminated following the instructions here, contact customer service.
PROBLEM
CAUSE
The machine does not
Electrical
start up
supply absent or
inadequate
Electrical
protection tripped
Motor does not start
Inadequate voltage
but makes a noise
Inadequate pressure
Nozzle blocked or
distorted
Valve dirty or worn
Vibrations
and/or
The
sucking in air
abnormal
water
discharge
Air in the hoses
Pump
worn
Suction
valves blocked
Pump noisy
Bearings worn
"White" oil
Seepage of water
into
(emulsion)
Water leaks
Gaskets
pistons worn
The water temperature
No diesel oil is
does not reach the
supplied
required level
Dirty diesel filter
photoresistor dirty
Broken thermostat
The heating pipe
coil is clogged with
calcareous
symbol, this means its disposal is
You
should
therefore
X
X
X
X
REMEDY
power
Check the characteristics
of the power line
Contact customer service
Check the characteristics
of the power line
Clean or replace
Contact customer service
pump
is
Check
water
connectors
Vent
the
air
disconnecting the hose
gaskets
Contact customer service
delivery
Unscrew
valve
remove and clean (ideally
contact customer service)
Contact customer service
Have
the
seal
the
oil
replaced
by
customer
service
and/or
Have
the
seal
replaced
by
customer
service
Fill the tank
Clean the diesel oil filter
Clean the photoresistor
Request the intervention
Request the intervention
seek
supply
by
caps,
pack
pack
Publicidad
