Descargar Imprimir esta página

WERKU WK402120 Instrucciones Originales página 4

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 6
ENG
the prevention of accidents, health and safety
directives, laws and applicable restrictions for
work places
The polisher must only be used
by persons who have been instructed in its use
and only for the purposes for which it has been
designed.
POWER SUPPLY.
Make sure the power supply is adapted to the
requirements shown on the information panel of
the polisher (1)
Using the motor at low voltage
will make it operate slowly
performance and may cause the motor to overheat.
EXTENSION CORD.
If the working area is at some distance from the
power supply, use an extension cord of enough
diameter and quality.
FITTING THE BACKING PAD.
Screw the support plate on the axis (2)
polisher is equipped with an axis blockade button.
press the blockade button by turning the support
plate until the complete introduction (3)
press blockade button when the support plate is
completely still
This button should only be used
for mounting and dismounting the support plate.
FIXING THE POLISHING BONNET.
Disconnect the polisher from the power supply
before making any adjustments or replacing
accessories
The polishing bonnet are held in
place with velcro (4)
over the plate so that their edges meet (5)
the polishing bonnet in place onto the base until it
is firmly held in place (6).
SAFETY BUTTON.
The polisher is fitted with a safety button (7)
start it, press the safety button and then press the
switch (8).
SPEED CONTROL.
Adjust with the buttons the speed control
depending on the different materials to work (9).
USING THE POLISHER.
Before starting to work, apply the correct
polishing product onto the work surface, which
may be of different types depending on the work
being carried out (polishing, buffing or waxing)
Click the switch to the 'on' position
This will reduce
Only
Align the polishing bonnet
Allow the
polisher to run for a few seconds until reaching the
correct speed
place the head of the polisher in contact with the
surface being worked on, pressing down gently
and using circular movements (10)
care not to press down on the polisher when
working on edges (11).
MAINTENANCE.
The polisher has been designed for a long
working life with minimum maintenance
use depends on correct care of the polisher and
regular cleaning
unplug the polisher from the power source
before cleaning or performing any maintenance
The polisher may be cleaned effectively using
compressed air after each use
is not available, use a brush to remove dust from
the polisher
The
levers must be dept clean and free of foreign matter
Do not attempt to clean by inserting pointed
objects through openings
and solvents damage plastic parts, among them
are gasoline, carbon tetrachloride, chlorinated
cleaning solvents, ammonia and household
cleaners containing ammonia
of these to clean the polisher
sparking occur, have a Werku
service exam and/or replace the carbon brushes.
ENVIRONMENT PROTECTION.
The materials and components that have
Press
been used to manufacture this product can be
re-used and recycled
an Integrated Management System that is in
charge of the correct elimination of the residues
of this product
with domestic residues
To
clients a free collection service of these residues
through any of its sale points, or in the collection
points established by the Integrated Management
System or in the recycling point of your locality.
WARRANTY AND TECHNICAL SERVICE.
Apart from the legal guarantee, Werku
an additional commercial guarantee
commercial guarantee covers the repair of all
defects found due to faults in the materials or
manufacture
4
English
Holding it firmly with both hands,
To prevent accidents, always
If compressed air
Motor ventilation vents and switch
Cetain cleaning agents
Do not use any
Should excessive
official repair
®
Werku
is adhered to
®
Do not eliminate this product
Werku
®
For this cover to be effective it is
Take special
Optimum
offers to its
offers
®
This

Publicidad

loading