Publicidad
Idiomas disponibles
Idiomas disponibles
User Instructions
AV Config
MENU
Name inputs
Speaker
config
Speaker
level trim
Speaker distance
Power amplifiers
Display mode
Clear settings
Exit setup
GB
GB
AV Master 8.0 Menu system
The AV Config menu runs in sequence through all the set-up menu settings necessary to configure your AV
Master 8.0 to best match your system components. The AV Config menu covers the following settings -
Speaker config + size and subwoofer crossover setting, Power amplifier setting, Speaker level trim (each
speaker in turn), Speaker distance (each speaker in turn).
Each input of the AV Master 8.0 can be given a name to match the source that is connected to it, such as
'DVD' or 'Tuner'. To name the inputs of your AV Master 8.0, select this menu option, and you will see a list of
the input numbers with their current names. To change a name, scroll to the input on the list and select it.
You can then scroll through a library of names to choose. If you have an input with no source connected,
select 'No source' and it will no longer be shown when operating the input selector..
Select this menu function to choose the number of speakers in your system. The number of speakers is
shown on the left of the display (choose the number of speakers followed by .1 if there is a subwoofer in
Speaker
setup
your system). There is also a graphic indication of the speaker layout in the room on the right of the display.
Choose the option that lists the speaker channels that you have connected to your AV Master 8.0.
After choosing the number of speakers in your system, enter the size of the speakers. Large speakers will
Speaker
have a good bass output and are generally floor standing. If you have a good quality system sub-woofer it
sizes
is advisable to set all system speakers to small.
If the subwoofer is enabled in the Speaker setup menu, then you will be asked if you wish to set the
subwoofer crossover. Crossover settings enable you to change the crossover frequency to values
between 40Hz and 250Hz, and also the crossover slope to 'Satellite roll-off' or 'Full X-over'. To use the full
bass response of your speakers, choose 'Satellite roll-offl' and set the crossover frequency to match the
bass roll-off of your speakers (this should be listed in your speaker specifications). To redirect deep bass
Crossover frequency
and rate
from your speakers to your subwoofer, choose 'Full X-over' and set the crossover frequency to
approximately double the bass roll-off frequency. The factory settings of Satellite/80Hz should match most
smaller stand-mount speakers.
NOTE:- Crossover settings are only effective for system speakers that are set to 'small' size in the Speaker
configuration menu.
This menu option is used to set the relative sound levels of the speakers. To make a particular speaker
Select speaker
louder or softer, select that speaker from the speaker list, then adjust the speaker loudness on the scale.
to adjust
Press the NOISE key on the remote control to run a noise sequence to assist with setting speaker levels.
00dB is the factory setting, +dB will set the level of the chosen speaker louder, -dB will set the level quieter.
Select this option to set the distance from each speaker to the listening position. Once these distances
Select speaker
have been set, the AV Master 8.0 will compensate for any differences in distance and ensure that the
to adjust
sound arrives from all the speakers in the system at the same time.
Choose this option to switch on the internal power amplifiers if they are required in your system. If either or
both of the power amplifiers are not required, they must be turned off for best performance.
There are three different selectable styles for the front panel display. Select either 'Large Decoding', 'Large
Input Names' or 'Large Volume', depending on your preference.
If necessary you can select this option to reset all Set-up menu settings to the original factory settings.
These are - All speaker channels (including sub-woofer) enabled with trims set to 0dB and distance set to
3m/10ft. Input names will be cleared and set back to Input 1, Input 2 etc. Input mode memory will be set to a
default of 'PLIIx Movie'. Left/Right and Centre power amplifiers will be switched on. Bass and Treble
controls are set to 'flat'. The Display Mode will be set to 'Large Input'.
Select this option to exit the set-up menu system.
Cyrus AV Master 8.0
5
Publicidad
