Publicidad
Idiomas disponibles
Idiomas disponibles
Specifications
Pipe Patch Installation Equipment
Packer/
Overall
Max.
Nominal
Packer
Patch
Pipe Ø
Length
Length
2"
43"
32"
3"
43"
32"
3" - 4"
4'
36"
3" - 4"
7'
68"
4" - 6"
4'
36"
4" - 6"
7'
68"
* Do not exceed packer operating pressure
** Minimum amount of exposed packer rubber at end of patch required for proper installation of patch.
Air Push Rod (For use with 3" and larger packers)
Nominal
Length ........................5' (1.5 m) each
Maximum
Reach .........................100' (30.5 m)
Maximum
Pressure .....................217 PSI (15 Bar)
Not for use through P-traps or 3" elbows
Air Hose Length ...........100' (30.5 m)
Pneumatic Connector
Type ..............................Locking
Adapter .........................Adapts standard air hose con-
nectors to locking style used with
RIDGID pipe patching equipment
Required Compressed Air
Supply ..........................100 psi to 130 psi (6.9 to 9.0 Bar)
Pull Rope ......................750 pound (3.3 kN) rating,
¼" (6.4mm) Diameter, 250' (76 m)
Long
Gloves ..........................Nitrile
2" RIDGID Pipe Patch
Elastic Bands ...............Specially sized for use with
RIDGID 2" packer
3" - 6" RIDGID Pipe Patch
Elastic Bands ...............Specially sized for use with
RIDGID 3" to 6" packers
999-995-411.10_REV A
22°, 45°,
Radius 90°
Minimum
Packer
Encroachment
Operating
Zone**
Pressure*
3"
43 psi
3"
60 psi
5"
50 psi
5"
50 psi
5"
36 psi
5"
36 psi
Short
Pipe Size
Long
Radius 90°
Transitions
Elbows
Elbows
and P-Trap
Y
Y
N
Y
Y
N
Y
4" Only
3" - 4"
Y
4" Only
3" - 4"
Y
6" Only
4" - 6"
Y
6" Only
4" - 6"
Pipe Patch Specifications
Pipe patch kits are available for a variety of inner pipe di-
ameters in various lengths. Refer to the RIDGID catalog
for specific offerings.
Patch Material ..............Fiberglass
Resin Type ...................Two-Component Organic Silicate
Resin Mix
Ratio .............................2:1 by volume, Controlled by
Resin Shelf Life ............One Year, Use By Date On
Resin Storage
Temperature .................41°F to 113°F (5°C to 45°C) Do
Resin Application
Temperature ................41°F to 68° F (5°C to 20°C)
Working Time
(Pot Life) .......................15 Minutes (At Resin Application
Resin Set Time ............90 Minutes (Internal Pipe Tem-
Pipe Patch
Air Push
Resin
Resin
Rods
Amount
Wet Out
10'
32"
Off
Integral
Packer
5'
32"
On
Sections
Packer
5'
3'
On
Sections
Packer
5'
2 x 3'
On
Sections
Packer
5'
3'
Off
Sections
Packer
5'
2 x 3'
Off
Sections
Packer
Mineral
Containers. Make sure both con-
tainers are marked the same (32"
or 3')
Carton/Resin Container
not allow resin to freeze
Temperature)
perature 50F° to 68°F (10°C to
20°C))
180 Minutes (Internal Pipe Tem-
perature 41°F to 49°F (5° to 9°C))
Pipe Patch
Elastic
Bands
2"
3" - 6"
3" - 6"
3" - 6"
3" - 6"
3" - 6"
5
Publicidad
