Manuales relacionados para Truper DES-430
Resumen de contenidos para Truper DES-430
- Página 1 Manual Gas grass trimmer Applies for: Codes Models 11031 DES-430 11032 DES-520 DES-430 DES-520 43 cc 52 cc Motor Read the user’s manual thoroughly CAUTION before operating this tool.
-
Página 2: Tabla De Contenido
Contents WARNING Technical Data Fuel Specifications To gain the best performance of the tool, prolong the duty life, Safety warnings for motor tools make the Warranty valid if necessary, and to avoid hazards Safety warnings for grass trimmers of fatal injuries please read and understand this Manual before Parts using the tool. -
Página 3: Technical Data
Technical data DES-430 DES-520 Code 11031 11032 Description Gasoline grass trimmer Net weight 20.2 lb Motor 43 cc 52 cc Motor rated power 1.7 Hp 2 Hp Fuel tank 0.3 gal Speed 9 000 RPM Cutting capacity 18” Axis length 5.2 ft... -
Página 4: Safety Warnings For Motor Tools
Safety warnings for motor tools Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the grass trimmer in explosive areas or in the of injury. -
Página 5: Safety Warnings For Grass Trimmers
Safety warnings for grass trimmers • In extreme temperatures verify there are no ice Fuel handling formations or condensation in the grass trimmer. • Verify visibility and light condition are adequate to see • Never smoke near fuel or where gasoline is supplied. Or where the oil mix is prepared or while operating the clearly. -
Página 6: Parts
Parts WARNING • Do not try to modify the grass Spark Plug Starter Fuel Handle Tank trimmer or manufacture not recommended accessories. Otherwise, the user may suffer severe injuries and will make the warranty void. WARNING • When assembling parts, always disconnect the motor spark plug cable to prevent an accidental start up causing severe personal injuries. -
Página 7: Assembly
Assembly Handle Guard • Separate the hinge bracket from the straight axis frame • Fasten the guard into the cutting head using the bracket loosening the easy adjusting knob (a). and the bolts included (A). • Set the handle in the straight axis frame. •... - Página 8 Assembly Line spool installation • Set the pressure turn table onto the cutter head (7). • Set the flange onto the turn table (8). • Insert the Allen key into the turn table side to block the axis (5). • Place the threaded spool in the axis and tighten counterclockwise using your hand (9).
-
Página 9: Fuel Supply
Fuel supply • Follow the safety standards for handling fuel (page 5). • Wait until the motor has cooled down completely before supplying fuel. • Set the grass trimmer onto a flat surface. • Wipe clean around the fuel tank cap to prevent contamination. -
Página 10: Turning Off
Turning on Start up with a hot motor • Set the grass trimmer on level ground where the blade or spool will not make contact with any obstacle. • Set the switch into the ON position (A). • Press simultaneously the trigger release (D) and the throttle trigger (E).Keep the trigger depressed. -
Página 11: Maintenance
Maintenance • Before inspecting, cleaning or servicing the tool turn the motor off, wait for all the mobile parts to stop, disconnect the spark plug cable and set it away from the spark plug. Otherwise, the operator may suffer severe burns and / or damage the tool. General cleansing Spark plug replacement •... -
Página 12: Regular Maintenance
Maintenance Gas Brushcutter Storage In the event of storing the Gas Brushcutter for one month or longer, bear in mind the following considerations: • Drain all the fuel tank contents into an approved gasoline container. All the remaining fuel can be re-used in another tool that uses 2-stroke motor with a 50:1 ratio. -
Página 13: Notes
Notes ENGLISH... - Página 14 Notes ENGLISH...
-
Página 15: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 0187-8737 to get information about the nearest Service Center. -
Página 16: Warranty Policy
. Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.