Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Transporting and storage
Warning! The rotating blade can cause serious injury.
Release bail bar to turn mower off and remove the safety key
before lifting, transporting or storing the mower. Store in a dry
place.
Note: The mower will not be as heavy to lift if the battery pack
is removed first. Do not use the latch as a lift point for the
mower.
Storage
In warm climates, to ensure optimal performance it is recom-
mended that the battery is maintained on constant charge.
The battery may be stored with the charger disconnected if
the following conditions are met.
The battery is fully charged before storing.
u
The average temperature of the storage location is below
u
10°C (50°F).
Troubleshooting
If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, release the bail bar to turn
mower off, wait for the blade to stop and remove the safety
key.
Problem
Possible solution
Machine fails to
Check to make sure the safety key has been
operate.
installed and is fully seated and that the lock
off button is being completely depressed
before moving the bail handle.
Release bail handle to turn mower off. Remove
safety key and battery pack, turn mower over
and check that blade is free to turn.
Check that the battery cavity is free of debris
and that the battery is installed properly.
Has battery been fully charged? Plug in
charger and wait for green light to come on
Motor stops while
Release bail handle to turn mower off. Remove
mowing.
safety key and battery pack. Turn mower over
and check that blade is free to turn.
Raise cutting height of wheels to highest posi-
tion and start mower.
Check that the battery cavity is free of debris
and is connected properly.
Has battery been fully charged? Press state of
charge button.
Avoid overloading the mower. Slow down the
cutting pace, or raise the cut height.
Machine leaves ragged
Has battery been fully charged? Press state of
finish or motor labours
charge button.
Release bail handle to turn mower off. Remove
safety key and battery pack. Turn mower over
and check:
u
u
Wheel height adjustment may be set too low
for grass condition. Raise cutting height.
16
(Original instructions)
Blade for sharpness - Keep blade sharp.
Deck and discharge chute for clogging.
Problem
Possible solution
Mower is too hard to
Release bail handle to turn mower off. Remove
push.
safety key and battery pack. Raise cutting
height to reduce deck drag on grass. Check
each wheel for free rotation
Mower is abnormally
Release bail handle to turn mower off. Remove
noisy and vibrates.
safety key and battery pack. Turn mower on
side and check blade to ensure it has not been
bent or damaged. If blade is damaged, replace
with a BLACK+DECKER replacement blade.
If the underside of the deck is damaged, return
mower to a BLACK+DECKER Authorized
service center.
If there is no visible damage to the blade and
the mower still vibrates:
u
u
u
u
u
If mower still vibrates, return the mower to
an authorized BLACK+DECKER authorized
service center.
Mower not picking up
Chute clogged. Release bail handle to turn
clippings with bag.
mower off. Remove safety key and battery
pack. Clear chute of grass clippings.
Raise cutting height of wheels to shorten
length of the cut.
Bag full. Empty bag more often.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled, reducing demand for raw materials. Please
recycle electrical products and batteries according to local
provisions. Further information is available at
www.2helpU.com
Technical data
V
36V
Input Voltage
DC
-1
min
No-Load Speed
3500
kg
Weight
16.2
Battery
BL2536
V
Voltage
36V
DC
Capacity
Ah
2.5Ah
Li-Ion
Type
BDC2A36
Charger
V
Input Voltage
230V
AC
Release bail handle to turn mower off.
Remove safety key and battery pack.
Disassemble entire blade assembly as
described in the "Removing and installing
blade" section.
Remove any debris and clean each
piece.
Replace each piece as described in the
"Removing and installing blade" section.
CLM3825
Publicidad
