Scope Of Delivery; Optional Equipment And Accessories; Technical Data; Control Unit - Reflex Reflexomat XS Manual De Instrucciones

Technical data

If the water level in the primary vessel falls below minimum, a fault message is
output from the controller and displayed in the app as well as via LEDs on the
control panel.
 Note!
Additional equipment for topping up water,  4.6 "Optional equipment
and accessories",  18.
4.5

Scope of delivery

The scope of delivery is described in the shipping document and the content is
shown on the packaging.
Immediately after receipt of the goods, please check the shipment for
completeness and damage. Please notify us immediately of any transport
damage.
Basic pressure-maintaining equipment:
• One 80-litre expansion vessel and one compact design control unit.
• "LIS" weight measuring cell for filling level measurement.
• Cap valve
• Mains cable with plug (230V~)
4.6

Optional equipment and accessories

• For make-up with water
– Solenoid "Fillvalve" with ball valve and Reflex Fillset for make-up
with potable water.
• Fillset Impulse with FQIRA+ contact water meter for make-up with potable
water.
• Fillsoft for softening or demineralisation of the make-up water from the
potable water system.
– Fillsoft is installed between Fillset and the device. The device
controller evaluates the make-up quantities and signals the required
replacement of the softening cartridges.
• Fillguard for conductivity monitoring
– If the Fillguard is fitted, the capacity of the Fillsoft Zero
demineralisation cartridge can be monitored based on the
conductivity.
• Optional expansions for Reflex controllers:
– RS-485 interface with Modbus RTU (integrated).
– Servitec S
– Fillcontrol
 Note!
Separate operating instructions are supplied with accessories.
5 Technical data
5.1

Control unit

Permissible ambient temperature
Degree of protection
Noise level
Electrical power
Electrical supply
Fusing
Electrical voltage control unit
Number of RS-485 interfaces
Weight
Permissible operating temperature
Permissible flow temperature
Operating pressure
Safety valve (PSv max)
Heating capacity
18 — English
+5 – +40 °C
IP 42
72 dB
max. 250 W
230 V / 50 Hz
4 A
230 V / 2 A
1
28 kg
0 – 70 °C
90 °C
0.5 - 3.5 bar
6 bar
Up to approx. 400 kW
Reflexomat XS — 02.16.2022 - Rev. A
5.2

Vessel

Vessel without controller (volume 80 l)
6

Installation

DANGER
Risk of serious injury or death due to electric shock.
If live parts are touched, there is risk of life-threatening injuries.
• Ensure that all phases of the mains power supply to the product are
disconnected prior to installation.
• Ensure that the system is secured and cannot be reactivated by other
persons.
• Ensure that installation work for the electric connection of the device is
carried out by an electrician, and in compliance with electrical
engineering regulations.
CAUTION
Risk of injury due to pressurised liquid
If installation, removal or maintenance work is not carried out correctly, there
is a risk of burns and other injuries at the connection points, if pressurised
hot water or hot steam suddenly escapes.
• Ensure proper installation, removal or maintenance work.
• Ensure that the system is de-pressurised before performing installation,
removal or maintenance work at the connection points.
CAUTION
Risk of burns on hot surfaces
Hot surfaces in heating systems can cause burns to the skin.
• Wear protective gloves.
• Please place appropriate warning signs in the vicinity of the device.
CAUTION
Risk of injury due to falls or bumps
Bruising from falls or bumps on system components during installation.
• Wear personal protective equipment (helmet, protective clothing,
gloves, safety boots).
WARNING
Risk of injury due to heavy weight
The devices are heavy. Consequently, there is a risk of physical injury and
accidents.
• Use suitable lifting equipment for transportation and installation.
 Note!
Confirm that installation and start-up have been carried out correctly
using the installation and commissioning certificate. This action is a
prerequisite for the making of warranty claims.
– Have the Reflex Customer Service carry out commissioning and
the annual maintenance.
6.1

Installation conditions

6.1.1

Incoming inspection

Prior to shipping, this device was carefully inspected and packed. Damages
during transport cannot be excluded.
Proceed as follows:
1. Upon receipt of the goods, check the shipment for
– completeness and
– possible transport damage.