Publicidad
Idiomas disponibles
Idiomas disponibles
BP
KEY BEEP function activated
MENU activated
CTCSS
A CTCSS tone is used in the active channel
DCS
A DCS code is used in the active channel
The channel is stored on the scan skip memory
Indicates the tone or code used
Indicates the active channel
TX or RX bargarph
Indicates Frequency, Menu or Message
4) AM/FM ~ PA ~ CTCSS/DCS
AM/FM
(short press)
This switch allows
selecting
the modulation mode AM, FM; Your modulation
mode has to correspond to the one of your correspondent.
Amplitude Modulation / AM: communication on a field with relief and
-
obstacles at middle distance (the most used).
-
Frequency Modulation / FM: for nearby communications on a flat open
field.
In U configuration only: in FM mode, a short press on the F key (9)
between the ENG or CEPT frequency bands. "UK" is displayed when the
ENG frequency band is selected (see table on page 70).
PA (Public Address)
(long press)
An external loud speaker can be connected to the unit by the PA jack plug
located on the back panel PA.SP. (D). Turn the VOL button (1) to adjust the
PA volume.
Long press AM/FM key (4) to
alternate
PA
For details on operating in
47.
CTCSS/DCS
For simplicity, in this manual we will speak of CTCSS/DCS code to indicate
both a CTCSS tone and a DCS code, of GENRE to indicate the kind of code
(CTCSS, DCS or OFF = no code). TYPE indicates whether this is a TX transmis-
sion or an RX reception and MODE specifies the operating mode, Identical
I d or different DF.
alternates
CB
PA
between
and
mode.
mode, consult the PA SETTING menu page
Consult the CODE SET menu page 48.
See list of codes on pages 73.
Note: Codes can only be used in FM. Each channel can have its own code.
-
Press the F key (9).
appears.
-
Press the AM/FM key (4) to
Activation
If a CTCSS/DCS code has been stored, it becomes active, "CTCSS" or "DCS"
icon is displayed on the screen.
In MODE I d, if no CTCSS/DCS code has been stored, the device emits an
error beep. Go to the CODE SET menu to store a CTCSS/DCS code.
In DF MODE, if no CTCSS/DCS code has been stored in either TYPE TX or TYPE
RX, the device emits an error beep. Go to the CODE SET menu to store the
CTCSS/DCS codes.
Deactivation
If a CTCSS/DCS code has been stored and "CTCSS" or "DCS" is displayed on
the screen, a short press on the AM/FM key (4) after F key (9) deactivates
the stored cde, "CTCSS" or "DCS" disappears, a deactivation beep sounds.
The memorized CTCSS/DCS code is kept in memory but no longer functions.
5) EMERGENCY CHANNELS ~ EMERGENCY CHANNEL SETTING
EMERGENCY CHANNELS
Emergency channels will be automatically
(5). First press : emergency channel 1 is activated. Second press: emergency
channel 2 is activated. Third press:
appears on the display when an emergency channel is activated.
See the table page 74 for default emergency channels.
EMERGENCY CHANNEL SETTING
EMG1
1.
Using the rotary knob (6)
select
nel. "EMG" must not appears on the display.
2.
Press the AM/FM key (4) to select the modulation mode of the selected
channel.
3.
Long press the EMG key (5).
message says:
4.
Press the PTT switch (12) ou the F key (9) to
BEEP function is activated, a long beep sounds to confirm the success of
the operation (consult the KEY BEEP menu page 46).
42
activate/deactivate
the CTCSS/DCS function.
(short press)
selected
by pressing the EMG key
return
to the current channel. "EMG"
a channel other than an emergency chan-
appears on the display, "EMG" blinks. The
.
validate
and exit. IF the KEY
Publicidad
