Publicidad
Idiomas disponibles
Idiomas disponibles
3.
When the configuration is selected, press the F key (9) during 1 second. The
letter corresponding to the configuration is continuously displayed and a
confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver and then
switching it on again.
See the frequency bands table at pages 70 to 72 / configuration table
page 74.
D) FUNCTIONS WITH THE PTT SWITCH
1) TALKBACK
hear
This function allows you to
or external speaker connected to the EXT.SP jack (E).
Press and hold the PTT switch (12) then press the F key (9) to
deactivate
the TALKBACK function.
When the function is active, "TALKBACK" blinks on the display for 3 seconds,
displaying the current level of the TALKBACK and then remains permanently
displayed.
2) TALKBACK LEVEL
This function allows to adjust the volume level of the TALKBACK.
1.
Activate the TALKBACK function.
2.
Press and hold the PTT switch (12) then turn the rotary CH knob (6) to
crease
(clockwise) /
decrease
TALKBACK.
3.
Release the PTT switch (12).
3) NOISE GATE
(PTT + VOX)
-
Press and hold the PTT switch (12).
-
Short press the VOX key (10) to
GATE. "
" is displayed when the function is active.
Noise Gate: Prevents amplification of background noise. This results in
optimized signal levels.
4) REPEATER / RELAY
(PTT + AM/FM)
WARNING! This function is valid only on the D frequency band. See the
configuration table page 74.
This function allows you to increase the range of your transceiver.
The radio receives on the current channel and transmits on the defined
channel.
your own modulation in the optional internal
activate
(counterclockwise) the volume level of the
activate
(On) or
deactivate
(OF) the NOISE
To activate this function you must define a TX channel (See REPEATER/RELAY
SETTING menu page 49).
-
Press and hold the PTT switch (12).
-
Short press the AM/FM key (4) to
the REPETER/RELAY function. The selection or "
channel has not still been selected, blinks during 3 seconds.
E) MENU
The order of 15 menus is as described in this manual. However, the menu
displayed by entering the MENU will be the last menu modified by user.
The procedure is the same whatever the function is:
Press F key (9).
is displayed.
Long press F key (9) to
/
1.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
select
the menu to set.
2.
Press EMG key (5) to
validate.
3.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
modify
the value of the parameter.
4.
New press on EMG key (5) to
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5.
If no key is pressed, the unit
in-
from the display.
Note: UP/DN buttons (13) on the microphone have the same effect as the
rotation of the rotary CH knob (6). PTT switch (12)
and
exists
MENU.
disappears.
1) COLOR
Press F key (9).
is displayed.
Long press F key (9) to
1.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
select
the
menu.
2.
Press EMG key (5) to
validate.
3.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
modify
the color of the display.
45
activate
or
deactivate
", if the transmission
enter
the MENU.
The current color blinks on the display.
validate
the chosen value. The parameter
exits
MENU after 10 seconds.
validates
enter
the MENU.
The current color blinks on the display.
disappears
the last setting
Publicidad
