Publicidad
Idiomas disponibles
Idiomas disponibles
SIMPLE KEY USER GUIDE
KEY PAIRING PROCESS:
PRIMARY DIAL POSITION (ADD 1 KEY)
Please follow the instructions below.
1.
Turn the dial on the EZ Installer to position 1.
2.
Insert a working key and turn the ignition to the ON position. Do not
start the engine.
3.
Ensure the EZ Installer cable is plugged into the OBDII port.
4.
Put on the seatbelt.
NOTE: This step is not necessary for pairing but keeps the vehicle from
beeping while you are listening for the EZ Installer to beep.
5.
Press and release the button on the EZ Installer and you will hear a
beep.
When the EZ Installer beeps twice, turn OFF the ignition and remove
6.
the key. The EZ installer will beep once.
7.
Insert the new key and turn the ignition to the ON position. Do not
start the engine. The EZ installer will beep twice.
8.
Turn the ignition OFF. The EZ installer will beep.
9.
Turn the ignition to the ON position with the same key. Do not start
the engine.
10.
After 10 seconds, the EZ installer will beep twice. Turn the ignition
OFF. The EZ Installer will beep.
Turn the ignition to the ON position with the same key. The EZ Installer
11.
will beep a success tune.
12.
Start the engine to test the key.
13.
Remove the key from the ignition and test the buttons on the remote.
NOTE: If you need to add a key after successfully pairing, you do not have
to unplug and reconnect the EZ Installer. The device will reset after about 10
seconds and you can start a new pairing process.
KEY PAIRING PROCESS: ALTERNATE DIAL
POSITION (ERASE ALL BUT 1 EXISTING KEY)
Please follow the instructions below.
1.
Turn the dial on the EZ Installer to position 2.
2.
Insert a working key and start the engine.
3.
Ensure the EZ Installer cable is plugged into the OBDII port.
4.
Put on the seatbelt.
NOTE: This step is not necessary for pairing but keeps the vehicle from
beeping while you are listening for the EZ Installer to beep.
5.
Press and release the button on the EZ Installer and you will hear a beep.
6.
When the EZ Installer beeps twice, turn OFF the engine and remove
6
SIMPLE KEY USER GUIDE
the key. The EZ installer will beep once.
7.
Insert the new key and turn the ignition to the ON position. Do not
start the engine. The EZ installer will beep twice.
Turn the ignition OFF. The EZ installer will beep.
8.
9.
Turn the ignition to the ON position with the same key. Do not start
the engine.
10.
After 10 seconds, the EZ installer will beep twice. Turn the ignition
OFF. The EZ Installer will beep.
11.
Turn the ignition to the ON position with the same key. The EZ Installer
will beep a success tune.
12.
Start the engine to test the key.
13.
Remove the key from the ignition and test the buttons on the remote.
NOTE: If you need to add a key after successfully erasing, you do not have
to unplug and reconnect the EZ Installer. The device will reset after about
10 seconds and you can turn the dial to a new position and start a new
pairing process.
FREQUENTLY ASKED QUESTIONS
Q: The EZ Installer beeps 7 times after pushing the button to initiate the
pairing process and won't pair the new key. What should I do?
A: Your vehicle allows a maximum of 6 paired keys. If the vehicle already
has the maximum paired keys, a new key cannot be paired. If the EZ
Installer beeps 7 times early in the pairing process, then it's indicating that
the maximum number of keys have been paired. Perform the Alternate Dial
Position function to erase all but 1 key and then add a new key. Any other
existing keys must then be added back in using the Add 1 Key function.
Q: Can I use the same EZ Installer on other vehicles?
A: No, the EZ Installer can only pair Simple Keys to one vehicle. You
have the ability to pair additional Simple Keys to the same vehicle.
Visit carkeysexpress.com/simple-key or your local retailer to purchase
additional keys. If the EZ Installer sounds three beeps with appr. at
1-second interval then faster beeps continuously, this signifies that the
device has already been used on another vehicle. Visit CarKeysExpress.
com/store or your local retailer to purchase additional keys.
Q: The EZ Installer beeps 3/4/5/6 beeps with approximately 1-second interval 3
times, then beeps continuously. What should I do?
A: When a problem occurs during pairing EZ installer will play Error beeps
before continuous faster beeps. The number of error beeps corresponds to
a specific error code as explained below.
7
Publicidad
