Descargar Imprimir esta página

WERKU WK400030 Instrucciones Originales página 4

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 8
ommended by Werku
sory can be attached to this power tool, it does
not assure safe operation. The rated speed of the
accessory must be at least equal to the maximum
speed marked on this power tool. Accessories run-
ning faster than their rated speed can break and
fly apart. The outside diameter and the thickness
of your accessory must be within the capacity rat-
ing of this power tool. Incorrectly sized accesso-
ries cannot be adequately guarded or controlled.
Threaded mounting of accessories must match
the spindle thread. For accessories mounted by
flanges, the arbour hole of the accessory must fit
the locating diameter of the flange. Accessories
that do not match the mounting hardware of this
power tool will run out of balance, vibrate exces-
sively and may cause loss of control. Do not use
a damaged accessory. Before each use, inspect
the accessory. If this power tool or its accessory is
dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
this power tool at maximum no-load speed for one
minute. Damaged accessories will normally break
apart during this test time. Position the cord clear
of the spinning accessory. If you lose control, the
cord may be cut or snagged and your hand or arm
may be pulled into the spinning accessory. Reg-
ularly clean this power tool's air vents. The mo-
tor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may
cause electrical hazards.
STORAGE.
Store this power tool out of reach of children and not
allow the handling of this power tool to people un-
familiar with the tool or the instructions. This power
tool is dangerous in the hands of untrained users.
MAINTENANCE.
Check moving parts for misalignment or binding,
there are no broken parts or other conditions that
may affect the operation of power tools. Power tools
are repaired before use when they are damaged.
Many accidents are caused by poorly maintained
power tools. Use power tools, accessories and
tool tips, etc. according to these instructions and
in the manner provided for the particular type of
power tool, taking into account the conditions work
and work to develop. The use of this power tool for
®
. Just because the acces-
applications other than those intended could result
in a dangerous situation. Please check your power
tool serviced by a Werku
using only identical replacement parts. This will
ensure the safety of the power tool is maintained.
CHECK CONDITION.
Make sure that all the screws in this power tool
are perfectly tightened. In cold climates or when
this power tool has not been used for a period,
allow this power tool to warm up by leaving it to
run empty for a few minutes, to ensure that all in-
ternal components are perfectly lubricated. Make
sure that the possible installed accessories are
perfectly fitted in place.
BEFORE STARTING WORK.
Make sure that this power tool is firmly supported
before using. Check that no one is standing be-
neath you when using this power tool in high areas.
Keep your hands away from all moving parts of this
power tool.
DURING THE OPERATION.
Do not leave this power tool operating without ha-
ving it firmly fixed. Only turn it on when you are
sure you have full control over it. Do not point this
power tool at anyone while in use. When operating
this power tool will produce vibrations. The screws
may gradually come loose, and possibly cause
faults or accidents. Keep your hands away from
all moving parts of this power tool.
AT FINISH WORKING.
Do not touch the possible accessories installed in
this power tool after use. It may be hot and cause
burns. Some materials worked with may contain
chemicals or toxic components. Avoid inhaling
these substances or allowing them to come into
contact with your skin. Use PPE designed to pre-
vent and protect against incidents of this kind.
OTHER SAFETY INSTRUCTIONS.
1) Maintain a firm grip on this power tool and position
your body and arm to allow you to resist kickback for-
ces. Always use auxiliary handle, if provided, for maxi-
mum control over kickback or torque reaction during
start-up. The operator can control torque reactions or
kickback forces, if proper precautions are taken. 2)
Never place your hand near the rotating accessory.
Accessory may kickback over your hand. 3) Do not
English
4
official repair service
®

Publicidad

loading