Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Repeat the spray solution, scrubbing and vacuuming
u
process as necessary. Empty tank between process for
best results.
Once area is cleaned, allow the area to completely dry
u
and check affected area for any remaining staining.
Note: Area may appear to still be stained while wet.
Please allow treated area 24 hours to dry completely
before further treatment.
Emptying and cleaning the collection tank (Fig. G, H, I,J)
Warning! Never use the vac without its foam filter.
There are two methods of cleaning the collection tank (7), a
quick empty method for liquid only waste and a thorough
clean out method for solid and liquid waste.
Emptying collection tank
Warning! DO NOT try to empty waste in the collection tank
(7) when still installed on the main body.
When fluid reaches the max. fill line (250ml), turn
u
the vacuum OFF.
Removing collection tank
Press the collection tank release button (6) .
u
Pull the collection tank (7) straight down and away from
u
the main body as illustrated in figure G.
Liquid only waste
Remove collection tank (7) from main body.
u
Place collection tank (7) over an appropriate disposal
u
area.
Pull the liquid plug (7a) and tilt the collection tank (7) to
u
drain liquid contents quickly.
Once drained, reinstall liquid plug (7a).
u
Install collection tank (7) onto main body until it "clicks"
u
firmly into position, resume cleaning.
When cleaning task is complete, follow Maintenance
u
instructions for cleaning and storage.
Solid and liquid waste
Warning! DO NOT try to empty waste in the collection tank
(7) when still installed on the main body.
Before the fluid reaches the max. fill line (250ml), turn
u
the vacuum OFF.
Remove collection tank (7) from main body.
u
Place collection tank (7) over an appropriate disposal
u
area.
While holding the bottom half of the collection tank,
u
unlock the latch (7b) at the front of the collection tank
(7) .
Open the collection tank (7) and pour the contents into
u
an appropriate container.
Rinse the collection tank (7) with water to remove leftover
u
debris.
Remove the air seperator (12) and rinse clean with water.
u
10
(Original instructions)
Remove the foam filter (13) and rinse clean with water
u
and allow to dry. Once dry and clean, install into place.
Close the collection tank (7) and lock the latch (7b),
u
ensuring the collection tank (7) is properly sealed.
Note: The foam filter is re-usable, do not confuse it with a
disposable filter, and do not throw it away when the product is
emptied. We recommend that you replace the foam filter every
6–9 months depending on frequency of use.
Note: Check to see if the air separator (12) is free of
water and debris. Clean if needed.
Install collection tank (7) onto main body until it "clicks"
u
firmly into position.and resume cleaning.
When cleaning task is complete, follow Maintenance
u
instructions for cleaning and storage.
Note: Maximum debris collection will only be obtained with a
clean filter, clean chute and an empty collection tank.
If debris begins to fall back out of the product after it is
switched OFF, this indicates that the collection tank is full and
requires emptying.
Wash the foam filter, chute and collection tank
u
regularly using warm, soapy water and ensure that it is
completely dry before using again.
It is very important that the filter is correctly in position
u
before use.
Note: Use only mild soap and damp cloth to clean the vac.
Never let any liquid get inside the vac; never immerse any part
of the vac into a liquid.
Warning! Make sure the vacuum is completely dry before
using it.
Note: To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (other than those listed in this
manual) should be performed by authorized service centers
or other qualified service organizations, always using identical
replacement parts.
Cleaning Chute & Nozzle (Fig. K)
Remove the chute and cap (5) by pulling the cap away
u
from the main body as illustrated in figure K.
The cap (5) can be lifted away from the chute to rinse and
u
wash each component.
Both components are dish washer safe (top rack only).
u
Ensure the chute and cap are dry before re-assembling.
u
Once cleaning is finished, attach cap onto the chute and
u
insert into the assembly into the front of the main body.
Removing and cleaning the manual scrub brush
BHSB315J only (Fig. L)
The manual scrub brush (8a) can be easily removed from the
vacuum head for cleaning.
Press down the tab (14) and remove the entire brush
u
assembly (8a).
Once the brushes have been cleaned, replace the brush
u
assembly, ensuring it clicks into place.
Publicidad
