Grounding Instructions; Important Electrical Information - WAGNER POWER PAINTER Manual De Usario

Important Safety
Safety Safety
Information
Read all safety information before operating
the equipment. Save these instructions
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
a) To reduce the risks of fire or explosion, electrical shock
and the injury to persons, read and understand all
instructions included in this manual. Be familiar with the
controls and proper usage of the equipment.

Grounding Instructions

This product must be grounded. In the event of an electrical short
circuit, grounding reduces the risk of electric shock by providing an
escape wire for the electric current. This product is equipped with a
cord having a grounding wire with an appropriate grounding plug.
The plug must be plugged into an outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
WARNING - Improper installation of the grounding
plug can result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary,
do not connect the green grounding wire to either flat
blade terminal. The wire with insulation having a green outer surface
with or without yellow stripes is the grounding wire and must be
connected to the grounding pin.
Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt
as to whether the product is properly grounded. Do not modify the
plug provided. If the plug will not fit the outlet, have the proper outlet
installed by a qualified electrician.
This product is for use on a nominal 120 volt circuit and has a
grounding plug that looks like the plug illustrated below. Make
sure that the product is connected to an outlet having the same
configuration as the plug. No adapter should be used with this
product.
Grounded Outlet
Grounding Pin
English
b) WARNING - To reduce the risk of fire
or explosion:
1. Do not spray flammable or combustible
materials near an open flame,
pilot lights or sources of ignition such as hot objects,
cigarettes, motors, electrical equipment and electrical
appliances. Avoid creating sparks from connecting and
disconnecting power cords.
2. For use with only water-based or mineral spirit-type
materials with a minimum flash point of 21ºC (70º F) —
Do not spray or clean with liquids having a flash point of
less than 21ºC (70º F). Flash point is the temperature at
which a fluid can produce enough vapor to ignite.
3. Verify that all containers and collection systems are
grounded to prevent static discharge.
4. Connect to a grounded outlet and use grounded
extension cords (electric models only). Do not use a 3 to
2 adapter.
5. Do not use a paint or solvent containing halogenated
hydrocarbons. Such as chlorine, bleach mildewcide,
methylene chloride and trichloroethane. They are not
compatible with aluminum. Contact the coating supplier
about compatibility of material with aluminum.
6. Keep spray area well ventilated. Keep a good supply of
fresh air moving through the area to keep the air within
the spray area free from accumulation of flammable
vapors. Keep pump assembly in well ventilated area. Do
not spray pump assembly.
7. Do not smoke in the spray area.
8. Do not operate light switches, engines, or similar spark
producing products in the spray area.
9. Keep area clean and free of paint or solvent containers,
rags, and other flammable materials.
10. Know the contents of the paint and solvents being
sprayed. Read all Material Safety Data Sheets (MSDS)
and container labels provided with the paints and
solvents. Follow the paint and solvent manufacture's
safety instructions.
11. Fire extinguisher equipment shall be present and working.
c) WARNING - To reduce the risk of skin
injection:
1. Do not aim the gun at, or spray any person or
animal.
2. Keep hands and other body parts away from the
discharge. For example, do not try to stop leaks with any
part of the body.
3. Always use the nozzle tip guard. Do not spray without the
nozzle tip guard in place.
4. Only use a nozzle tip specified by the manufacturer.
5. Use caution when cleaning and changing nozzle tips.
Cover for
6. High-pressure spray is able to inject toxins into the body
grounded
outlet box and cause serious bodily injury. In the event that injection
occurs, seek medical attention immediately.
7. This system is capable of producing 2800 PSI / 193
8. Verify that all connections are secure before operating the
d) WARNING - To reduce the risk of injury:
1. Always wear appropriate gloves, eye protection, clothing
2. Do not operate or spray near children. Keep children
3. Do not overreach or stand on an unstable support. Keep
4. Stay alert and watch what you are doing.
5. Do not operate the unit when fatigued or under the
e) WARNING - To reduce the risk of electric
1. Keep electrical cord plug and spray gun
2. Never immerse electrical parts in water or any other

Important Electrical Information

ImpoRTANT: Use only a 3-wire extension cord that has
a 3-blade grounding plug and a 3-slot receptacle that will
accept the plug on the product. Make sure your extension
cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your
product will draw. For lengths less than 50 feet, use a No.
18 AWG extension cord. For lengths more than 50 feet, use
a No. 14 or No. 16 AWG extension cord. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating.
Wagner Spray Tech accessory extension cords recommended:
P/N 0090241
P/N 0090242
2
Bar. Only use replacement parts or accessories that
are specified by the manufacturer and that are rated a
minimum of 2800 PSI. This includes spray tips, nozzle
guards and extensions.
unit.
and a respirator or mask when painting. Hazardous
vapors – Paints, solvents, insecticides, and other
materials can be harmful if inhaled or come in contact
with body. Vapors can cause severe nausea, fainting or
poisoning.
away from equipment at all times.
effective footing and balance at all times.
influence of drugs or alcohol.
shock:
trigger free from paint and other liquids.
Never hold cord at plug connections to support cord.
Failure to observe may result in an electrical shock.
liquid. Wipe the exterior of the sprayer with a damp cloth
for cleaning. Always make sure the sprayer is unplugged
before taking it apart for cleaning.
20 foot extension cord
35 foot extension cord