Publicidad
Idiomas disponibles
Idiomas disponibles
suitable for washing cars, car trailers, buildings, boats, ceramic tiles,
etc. Appropriate accessories allow you to mix cleaning agents. The
device is placed on an ergonomic trolley with handles for
accessories and a reel for high-pressure hose.
Do not use the device contrary to its intended use.
DESCRIPTION OF THE GRAPHIC SIDES
The numbering below refers to the components of the device shown
on the graphic pages of this manual.
1. Transport handle
2. Hanger for high pressure hose
3. Switch
4. High pressure hose connection
5. Accessory holder
6. Fastening the transport handle
7. Quick coupler with built-in filter
8. Gun lock
9. Quick-disconnect gun pressure hose connection
10. Quick lance coupling
11. Quick lance coupling
12. Quick lance coupling
13. Quick lance coupling
14. Stream regulator
15. Detergent container
* There may be differences between the drawing and the product.
EQUIPMENT AND ACCESSORIES
1. Pistol (folding lance)
2. Detergent container
3. Quick coupler with filter
4. Hanger for accessories
5. Power cord holder
6. Screws
7. Nozzle pin
8. User manual
9. High pressure hose
PREPARATION TO WORK
PREPARATION TO WORK
• Screw the quick coupling with the built-in filter (7) onto the water
inlet.
• Install the power cord hanger (2) and the accessory holder (5) by
inserting them into the device guides from above.
• Screw the handle to the device with two screws (6).
• Connect the gun (lance) with the quick coupler (10 and 11) by
inserting the quick couplers and turning them about 45˚, connect
the quick couplers (12 and 13) by pushing them together until the
connection is locked. To disconnect them, release the connection by
pressing the button on the connector (12).
• connect the high pressure hose to the quick coupling of the gun
pressure hose (9).
ADJUSTMENT OF PRESSURE AND STREAM RATE
The nozzle (14) enables smooth adjustment of the size of the stream
from point to wide through its rotational movement (tightening /
unscrewing
The spot stream should be used for washing small, heavily soiled
surfaces. The wide jet is used to wash large, lightly soiled surfaces.
OPERATION / SETTINGS
ON / OFF
The mains voltage must correspond to the voltage specified on the
washer's rating plate.
- 1 pc.
- 1 pc.
- 1 pc.
- 1 pc.
- 1 pc.
- 2 pcs.
- 1 pc.
- 1 pc.
- 1 pc.
Before using the pressure washer, make sure that there are no other
people or pets in the workplace.
It is not allowed to use the washer without first unwinding the high
pressure hose from the drum. Do not kink the high pressure hose.
When using the washer, it is recommended to hold the pistol grip
with one hand and the lance with the other hand. Holding it with
both hands protects against uncontrolled kickback of the lance at
the time of starting and working.
Prior to operation, the pistol grip trigger should be pulled in to
purge air from the pump and high pressure hose.
Turning on
• Make sure the pressure washer is properly assembled and ready
for use.
• Connect the water supply to the quick coupler (7).
• Unwind the high-pressure hose and connect it to the quick coupler
of the device (4) and the quick coupler of the gun (9) by inserting it
into the connector opening until it locks.
• Check that the switch (3) is in the off position "0FF / 0"
• Open the water tap fully. Check the tightness of the connections.
• Unlock the pistol grip trigger with the trigger lock switch (8).
• Press the trigger of the gun fully until the water flow is even and
there is no air in the device and high pressure hose
• Release the gun trigger and lock it with the trigger lock lever (8).
• Connect the plug of the power cord to the mains socket.
• Turn on the device by setting the switch (3) to the "ON / I" position.
Note! Before turning on the washer, always make sure that
water flows through the device, which means that there is no
air in it.
• Release the trigger lock lever (8) and point the nozzle outlet onto
the test surface.
• Adjust the water flow. Perform the final wash.
• To temporarily turn off, release the pressure on the trigger, the
device will enter Stand-by mode.
• As soon as the trigger switch is pressed again, the high pressure
washer will reactivate.
Attention! Whenever you put the gun down or not use it, lock
the gun with the lock switch (8).
Turning off
• Release pressure on trigger. Secure with trigger lock lever (8). The
drain is blocked and the washer cannot be accidentally started.
• Turn off the device by setting the switch (3) to the "0FF / 0"
position.
• Turn off the water supply.
• Disconnect the device from the power socket.
• Release the trigger lock (8), and squeeze the trigger fully until
there is no more pressurized water in the unit.
• Release trigger and re-lock trigger lock (8).
• Disconnect the connection hose from the device and the water
connection.
• After the washer is turned off, the pressure remains inside. Do not
direct the stream of water at people, animals, electrical equipment
and the device itself, even after the washer is turned off.
• Ambient temperature during operation with the washer should be
between 5˚C and 40˚C.
DETERGENT SPRAY
The washer is designed for use with cleaning agents intended for
this type of devices. The use of other cleaning agents may adversely
affect the safety of the appliance. Do not use acids, gasoline,
kerosene or other flammable liquids as a cleaning agent. Only
household detergents (pH 6 ÷ 8) can be used.
Some surfaces may be damaged by the high pressure water jet.
10
Publicidad
