Care And Maintenance - VERTO 52G401 Instrucciones De Uso

To use the detergent, fill the attached detergent container (15) with
it and mount it in the lance using the quick couplers.
IMMEDIATE STOP SYSTEM
The pressure washer is equipped with an immediate stop system to
protect the engine. When the pistol grip trigger is released, the
engine stops. Squeezing the trigger switch will restart the engine.
DRAIN LOCK
If there is a need to temporarily stop the operation, it is absolutely
necessary to secure the trigger with the trigger lock lever (8) on the
pistol grip in order to avoid accidental activation.
ENGINE PROTECTION
The electric motor is equipped with a safety switch. Using the safety
switch, the motor stops when it is overheated. Turn off the device
and wait 20-30 minutes for the washer to cool down before
restarting the device.

CARE AND MAINTENANCE

RECOMMENDED CLEANING METHOD
Stage 1: Dissolving the contamination
Spray a small amount of the preparation on the surface and leave it
for a short time.
Stage 2: Removal of contamination
Remove the dissolved dirt (before it dries) with a high-pressure
water jet.
Never bring the nozzle closer than 30 cm to the washed surface (in
case of any doubts whether the water pressure will not cause any
damage, first test on a small area in an invisible place).
Never use the washer to clean surfaces that easily peel off the
surface coating.
Always run a stream of water over the surface to be washed. The jet
must not be allowed to fall in one place for a long time, as this may
damage the surface.
Before starting pressure washing, always consult the supplier of the
product to be washed as to whether the surface of the product is
suitable for such a procedure.
CARE AND MAINTENANCE
Before commencing any installation, adjustment, repair or
maintenance activities, disconnect the power cord plug from the
power socket.
CLEANING
The body of the washer, pistol grip, pressure hose and lance should
be kept clean.
The prerequisite for an effective cleaning process is to keep the
nozzle clean.
Clean the nozzle regularly using the nozzle cleaning pin.
Any repairs of the washer should be entrusted only to a qualified
person, using original parts.
A damaged power cord should be replaced by a qualified
electrician.
There are no user-serviceable or serviceable parts inside the washer.
In the event that it is necessary to repair the internal parts of the
washer, the device should be delivered to an authorized service
center.
Clean the external parts of the device thoroughly with a soft brush
and a cloth. Do not use water, solvents and rinse aid.
Remove all debris, especially from the engine vents.
STORAGE
Disconnect the pistol grip, pressure hose and lance from the washer
and store them in the accessory holder in a dry place.
If the device is not completely drained of water, it may be damaged
by low temperatures (risk of water freezing in the washer).
Store the device in a place protected against low temperatures.
If the device is not used for some time in rooms where there is a risk
of frost, it is recommended to fill the washer pump with a frost
protection agent (a measure similar to that used for car cooling
systems).
If the device is not used for a long time, limescale deposits are
formed in the electric pump, which can lead to problems with
starting the device.
Do not place any objects on the housing of the device.
Store the washer out of the reach of children.
FILTER CHECK
In order to avoid clogging of the device, which may damage the
pump, periodically check the filter in the power quick-coupler (7).
Unscrew the connector (7) from the device, rinse the internal filter
with water and replace it. If damaged, replace.
Never use the washer without a filter or with a damaged filter.
TRANSPORT
The washer can be transported to the workplace by rolling it on
wheels, using the transport handle.
All kinds of faults should be removed by the manufacturer's
authorized service.
To save space, wind the power cord around the handle (2).
TECHNICAL PARAMETERS
RATED DATA
Pressure Washer 52G401
Parameter
Supply voltage
Power frequency
Rated power
Protection class
Level of security
Max. supply water pressure
Rated water flow
Maximum water flow
Working pressure
Max. working pressure
Ambient temperature
Max. supply water temperature
Mass
Year of production
52G401 stands for both the type and designation of the
NOISE AND VIBRATION DATA
Sound pressure level
Sound power level
Vibration acceleration value
Information regarding noise and vibration
The level of noise emitted by the device is described by: the level of
the emitted sound pressure LpA and the sound power level LwA
(where K is the measurement uncertainty). The vibrations emitted
by the device are described by the value of the vibration
acceleration ah (where K is the measurement uncertainty).
The levels of emitted sound pressure LpA, sound power level LwA
and vibration acceleration ah given in this manual were measured
in accordance with IEC 60335-2-79. The stated vibration level ah can
be used for the comparison of devices and for the initial assessment
of vibration exposure.
11
Value
230V AC
50Hz
1400W
II
IP X5
12 bar (1,2 MPa)
5,5 l/min
6,5 l/min
80 bar (8 MPa)
110 bar (11 MPa)
5°C÷40°C
50°C
5,5 kg
2021
machine
Lp = 74,6 dB(A) K= 3 dB(A)
A
Lw = 88,3 dB(A) K= 3 dB(A)
A
a = 2,089 m/s 2 K= 1,5 m/s
h
2