Chicco Next2me Magic EVO Manual Del Usuario página 17

SIDE SLEEPING CONFIGURATION (FASTENING THE CRIB
TO THE BED)
The crib can be fastened to the parents' bed (side sleeping con-
figuration).
WARNING - IMPORTANT FOR YOUR CHILD'S SAFETY: This
configuration is allowed only with beds that allow compliance
with all the conditions described in this paragraph.
16. Specifically, the lowered side of the crib must always be po-
sitioned against the adult bed mattress, and, the adult bed
mattress must be aligned with (or at most slightly higher
than) the side of the crib. (Fig. 22A-22B). Moreover, the crib
must be fastened to the structure of the adult bed or to the
mattress support (mesh or slat sprung base).
WARNING: Check that the structure of the crib in side sleeping
configuration does not interfere with the parents' bed.
WARNING: During use, make sure that the bedsheets, blan-
kets, etc. do not interfere with the crib's space.
17. Lower the drop side of the crib by pushing button "E3" and
accompanying the side until it reaches the end of its travel
(Fig. 23).
WARNING: Use the crib with the drop side lowered only in side
sleeping mode.
18. Put the crib against the parents' bed and check its height
compared to the parents' mattress (Fig. 24).
WARNING: The top of the adult bed mattress must be higher
than or the same as that of the side of the crib. If this is not the
case, use the adjustment system to achieve this condition on
both sides.
WARNING: In side sleeping configuration, the 2 leg supports
of the crib must be set at the same height
19. To fasten the crib to the adult bed (side sleeping configura-
tion), use the pair of supplied straps "G".
20. Fasten the grey prongs "G1" to the grey buckles "E7" under
the fabric cover on either side. Make sure that the red buck-
les "G2" are positioned above the belt strap (Fig. 25).
21. Then run the strap around the structure of the adult bed
from the bottom up (Fig. 26) and fasten the red buckle
"G3" to the red prong "G2" forming a noose (Fig. 27). Repeat
this operation on the other side as well. To make installa-
tion easy, when fastening the buckles, always keep the crib
slightly away from the parents' bed.
22. Put the crib up against the parents' bed and tighten the loop
by pulling firmly on the straps (Fig. 28). Carry out this step
first on one side and then on the other, adjusting the straps
until the crib is in firm contact with the parents' mattress.
WARNING: Before each use, make sure that there is no space
between the adult bed mattress and side of the crib. Otherwise
adjust the straps pulling them until the required condition is
restored. Make sure that the side is always free to be lowered
and raised completely.
23. If the wheels are unlocked, lock the crib wheels as described
in point 13.
If when fastening the crib to the adult bed it is not possible to
fit the crib's feet under the adult bed, the bed can be fastened
anyway by the following the instructions above, with the add-
ed step of rotating the feet "B" when putting the crib against
the bed.
To rotate the feet press the release button "A7" and use one
hand to rotate the feet of the crib inward (Fig. 29).
24. To close the drop side simply lift it upwards, holding it from
the centre (Fig.30). Always make sure that it is engaged cor-
rectly.
WARNING: Whenever the drop side is lowered, make sure
that the position compared to the adult bed mattress has not
changed from that illustrated in the paragraphs above.
WARNING: NEVER USE the rocking function when the crib is
in "Side sleeping configuration (fastened to the bed). "
WARNING: When the product is used in "Co-sleeping configu-
ration (fastened to the bed), " it must always be mounted on the
long side of the bed. DO NOT install the product at the head or
foot of the bed.
CARE AND MAINTENANCE
The crib and mattress have a fabric lining that can be removed
and washed.
To remove the fabric, follow the instructions in the paragraph
"REMOVING THE FABRIC. "
WARNING: Covering or removing the fabric may take a few min-
utes and must be carried out by an adult.
Regularly inspect the product for signs of wear and damage.
In the case of damage, do not use and keep out of reach of
children.
When washing the fabrics pay close attention to the instruc-
tions on the label.
Do not use solvents, abrasive or overly aggressive products.
Hand wash
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Check that the fabric and the stitching are in good condition
after each wash.
WARNING: When covering or removing the cover, take care
when handling the fabric parts to avoid accidental tears or
damage.
WARNING: The fabric part of the drop side cannot be removed.
MAKING THE BED
The crib can be unfastened from the parents' bed when making
the bed.
25. Just unfasten the grey buckles under the fabric lining.
When fastening the crib again to the parents' bed, pull the
straps again to make sure that the crib is correctly and secure-
ly fastened to the parents' bed. Make sure that all the steps il-
lustrated above in "Co-sleeping configuration (fastened to the
bed)" have been completed.
REMOVING THE COVER
26. Remove the mattress from the crib.
27. Disconnect the crib frame "E" from the leg supports "A" by
pressing the buttons "E2.3" and gently moving the legs out-
wards (Fig. 31A-31B). Complete one side first then the other.
28. Remove the lateral support struts "F" by pressing the tabs
(Fig. 32) and pushing the base of the crib "E4" upwards (Fig.
33). Subsequently, press the pins placed in the upper at-
tachments "E5" and remove the struts completely (Fig. 34).
29. Release the upper attachment buttons "E8.3", the lower at-
tachment buttons "E8.4" and the two straps with the snap
buttons "E8.5".
30. Open the upper zipper "E8.2" and the two vertical zippers
"E8.1" (Fig. 35).
31. The fabric can now be removed completely, carefully pull-
ing it off the leg support inserts "E2" and the attachments for
the upper struts "E5".
DISASSEMBLING THE CRIB
WARNING: This operation must be carried out when no chil-
dren are present nearby.
The crib can be disassembled completely to put it away in the
supplied bag. To continue disassembling the crib, repeat the
17