Publicidad
Idiomas disponibles
Idiomas disponibles
set to the 1-dot minimum heat setting.
STEP 4: To iron with steam, move the steam control switch to the steam
position (centre).
STEP 5: After use, rotate the control dial to the 'MIN' position and move
the steam lock to the 'OFF' position. Switch off and unplug the iron from
the mains power supply and allow to cool thoroughly.
Note: Allow the iron to fully heat up before using the steam
function; not doing so may cause water to leak from the stainless
steel soleplate.
The temperature indicator light will illuminate whilst the iron
is heating up but not when it is cooling down; it should not be
misinterpreted as a ready-to-use indicator light.
The temperature indicator light will cycle on and off during use to
regulate the temperature.
Warning: Do not use the iron on any area of fabric for long periods
of time, as this will damage the fabric.
IRONING WITHOUT STEAM
For removing creases from more sensitive fabrics, try ironing without
steam
STEP 1: Slide the steam control switch to the 'OFF' position.
STEP 2: Plug in and switch on the iron at the mains power supply.
STEP 3: To increase the temperature of the iron, rotate the control
dial in a clockwise direction until the desired heat setting is reached.
Reduce the temperature by rotating the control dial in an anticlockwise
direction. The temperature indicator light will illuminate to signal that
the iron is heating up; this will switch off once the iron is ready to use.
STEP 4: Test the iron on a small area of the fabric to check that the
selected temperature is suitable; adjust if necessary.
STEP 5: After use, rotate the control dial to the 'MIN' position. Switch
off and unplug the iron from the mains power supply and allow to cool
thoroughly.
STEAM BURST FUNCTION
For creases that are stubborn and difficult to remove, use the steam
control switch to select the desired steam setting; if necessary, press
the steam burst button for extra steam. Wait approx. 5 seconds in-
between each burst to prevent any water leaking from the steam holes.
VERTICAL STEAM IRONING
Instruction manual
The steam burst button can also be used to vertically steam curtains
and other hanging garments.
STEP 1: Hang up the item to be vertically steamed.
STEP 2: Rotate the steam control switch to the off position.
STEP 3: Fill the water tank following the instructions in the section
entitled 'Filling the Water Tank'.
STEP 4: Plug in and switch on the iron at the mains power supply.
STEP 5: Rotate the temperature control dial until the 3-dot heat setting
is selected; the higher the temperature, the more powerful the steam.
STEP 6: Hold the iron approx. 15 cm away from the item and press the
steam burst button to remove any creases, waiting approx. 5 seconds
in-between each burst.
WATER SPRAY FUNCTION
The water spray function can be used to help remove stubborn creases
on heavier fabrics
It can also be used when dry ironing delicate fabrics that cannot be
steam ironed. To use the water spray function, hold the iron over the area
to be ironed and then press the water spray button
Note: The water spray function will not work if the water tank is
empty.When using the water spray function for the first time, it
may be necessary to press the water spray button several times.
ANTI-CALCIUM FEATURE
The iron has a built-in anti-calc filter located in the water tank to
prevent calcium and limescale build-up. Calcium build-up, which is
prominent in areas with hard water, can hinder performance and lower
the lifespan of the iron. This is an automatic feature that is permanently
activated.
SELF-CLEAN FUNCTION
The self-clean function removes limescale and impurities from within
the stainless steel soleplate.
It is recommended to use this function on a fortnightly basis or more
often if the iron is used in a hard water area.
STEP 1: Switch off and unplug the iron from the mains power supply.
STEP 2: Slide the steam control switch to the off position.
ref. 07714
ES
PT
EN
FR
Publicidad
