Publicidad
4. Level 1 - Resetting to factory settings (factory reset)
- Aim: you want to clear the drive settings. There are three options to choose from: I.) Clearing the
programming for your window and any other settings on the advanced menu (see 5.). II.) Clearing
all saved transmitters. III.) Complete factory reset
- Press keys 1 + 2 simultaneously, after a short time LED1 turns green.
- Press key 2 twice in succession; LED1 turns red.
- Confirm your intention to carry out a factory reset by pressing key 4
- LED1 is red, LED2 is green = option I. This position resets the programming process and
all settings on the advanced menu
- Pressing key 1 or 2 switches to option II or option III: LED1 is red, LED2 is yellow = option
II. This position clears all transmitters (remote controls, keypad).
LED1 is red, LED2 is red = option III. This position triggers a complete factory reset. The
drive is then in its delivered condition
- With the LED display required, press and hold key 4 for approx. 2 seconds; both LEDs
flash alternately
- Press and hold key 4 again for approx. 2 seconds and the reset is carried out. An
acoustic confirmation follows and the LEDs go out.
- To exit the menu item, press key 3
5. Level 2 - Advanced menu settings
The settings on the advanced menu are optional. You can modify the default values for the drive
on three submenus: A) Signal tones, B) Torque and C) Tilt function.
To access level 2, first complete the following two steps:
- Press keys 1 + 2 simultaneously, after a short time LED1 turns green.
- Press keys 1 + 2 simultaneously again, after a short time LED1 flashes green.
A) Signal tones (LED 1 flashes green)
- Confirm your intention to change the signal tones by pressing key 4
- Choose the required setting by pressing key 1 or 2:
LED 1 green / LED 2 green: signal tone in all end positions (factory setting)
LED 1 flashes green / LED 2 lights yellow: signal tone on motorised locking
LED 1 flashes green / LED 2 lights red: no signal tones*
* Alarm signals for required battery change, overload of the drive and magnetic displacement
(attempt at burglary) and key tones for the drive cannot be switched
off!
B) Torque
- Switch to this menu item by pressing key 2. LED1 flashes yellow
- Confirm your intention to change the torque by pressing key 4
- Choose the required setting by pressing key 1 or 2:
LED 1 flashes yellow / LED 2 lights green: torque restriction set (ca. 6 Nm).
LED 1 flashes yellow / LED 2 lights red: maximum torque (ca. 8 Nm)
C) Setting the tilt function
- Switch to this menu item by pressing key 2. LED1 flashes red
- Confirm your intention to activate the tilt function by pressing key 4
- Choose the setting required by pressing key 1 or 2:
LED 1 flashes red / LED 2 lights green: tilt function inactive
LED 1 flashes red / LED 2 lights red: tilt function active*
* If this setting is chosen, the window moves when pressing the transmitter's „open" button
from the tilt position to the "open" position. In doing so, the window must always be
brought in manually!
30
When using the tilting function, always pull the window by hand until the drive has
reached its rest position before actuating the drive! In particular with older windows and
patio doors, there is a risk that the casement will be lifted out of its anchoring, when it is
not brought in manually.
1. 1.
2. 2.
In case you hear a signal tone five times immedia-
tely after unlocking and opening the device (both
electronically with remote control or keypad, and
mechanically with a key), most likely there has
been an attempted burglary.
Please check your window for possible evidences of
a forced entry and, if need be, inform the police.
3. 3.
4. 4.
(Note: do not confuse the five sustained tones with
the five short tones that indicate a battery change
is due that take place before the drive starts to
move!)
31
Publicidad
