DeWalt DCS520 Traducido De Las Instrucciones Originales página 16

English
Fig. L
4
Dust Extraction (Fig. A2)
Your tool is fitted with a dust port

WARNING: DO NOT direct sawdust toward yourself
or others. DO NOT insert foreign objects into the
exhaust opening.

WARNING: ALWAYS connect the track saw to a dust
extractor!

WARNING: ALWAYS use a dust extraction device
designed in accordance with the relevant regulations
regarding dust emission.

WARNING: Static charge may occur if an anti-static
suction hose is not used.
A universal 1-1/4" dust extraction hose can be connected to
the dust port 17 . Check for a tight connection before use.
Dust Duct Cleaning
Depending on your cutting environment, saw dust can clog
the dust duct and may prevent dust from flowing away
from the cutting area properly. With the battery removed,
low pressure air or a large diameter dowel rod can be used
to clear the dust out of the dust duct.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
14
23
.
17
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of
an insurance loss, such as fire, flood or theft, your
registration of ownership will serve as your proof
of purchase.
• FOR YOUR sAFETY: Registering your product will
allow us to contact you in the unlikely event a safety
notification is required under the Federal Consumer
Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to
e
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by
others. This warranty gives you specific legal rights and
you may have other rights which vary in certain states
or provinces.
In addition to the warranty, D
by our:
WALT
e
WALT Industrial
e
WALT factory
e
WALT (1-800-433-9258).
e
WALT tools are covered
e