Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Set the action mode changing knob to the
You can drill up to 13 mm(1/2") diameter in metal and up
to 32 mm(1-1/4") diameter in wood.
CAUTION:
•
Never use "rotation with hammering" when the drill
chuck assembly is installed on the tool. The drill
chuck assembly may be damaged.
Also, the drill chuck will come off when reversing
the tool.
•
Pressing excessively on the tool will not speed up
the drilling. In fact, this excessive pressure will only
serve to damage the tip of your bit, decrease the
tool performance and shorten the service life of the
tool.
•
There is a tremendous twisting force exerted on the
tool/bit at the time of hole breakthrough. Hold the
tool firmly and exert care when the bit begins to
break through the workpiece.
•
A stuck bit can be removed simply by setting the
reversing switch to reverse rotation in order to back
out. However, the tool may back out abruptly if you
do not hold it firmly.
•
Always secure small workpieces in a vise or similar
hold-down device.
•
When performing diamond core drilling operations,
always set the change lever to the
use "rotation only" action. If performing diamond
core
drilling
operations
hammering" action, the diamond core bit may be
damaged.
MAINTENANCE
CAUTION:
•
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection
or maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by Mak-
ita Authorized or Factory Service Centers, always using
Makita replacement parts.
ACCESSORIES
CAUTION:
•
These
accessories
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury
to
persons.
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
SDS Plus Carbide-tipped bits
•
Drill chuck assembly
symbol.
position to
using
"rotation
or
attachments
Only
use
accessory
•
Drill chuck S13
•
Chuck adapter
•
Chuck key S13
•
Bit grease
•
Depth gauge
•
Blow-out bulb
•
Dust cup
•
Dust extractor attachment
•
Safety goggle
•
Plastic carrying case
•
Core bit
•
Side grip
•
Bull point (For HR2455 only)
•
Cold chisel (For HR2455 only)
•
Scaling chisel (For HR2455 only)
•
Grooving chisel (For HR2455 only)
•
Scraper (For HR2455 only)
•
Keyless drill chuck
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested
before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period of
ONE YEAR from the date of original purchase. Should
with
any trouble develop during this one year period, return
the COMPLETE tool, freight prepaid, to one of Makita's
Factory or Authorized Service Centers. If inspection
shows the trouble is caused by defective workmanship or
material, Makita will repair (or at our option, replace)
without charge.
This Warranty does not apply where:
•
repairs have been made or attempted by others:
•
repairs are required because of normal wear and
tear:
•
the tool has been abused, misused or improperly
maintained:
•
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAM-
AGES FROM THE SALE OR USE OF THE PRODUCT.
THIS DISCLAIMER APPLIES BOTH DURING AND
AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED
WARRANTIES, INCLUDING IMPLIED WARRANTIES
are
OF "MERCHANTABILITY" AND "FITNESS FOR A SPE-
CIFIC PURPOSE," AFTER THE ONE YEAR TERM OF
THIS WARRANTY.
or
This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to state.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limi-
tation or exclusion may not apply to you. Some states do
not allow limitation on how long an implied warranty lasts,
so the above limitation may not apply to you.
8
EN0006-1
Publicidad
Tabla de contenido
