Narex EV 13 F-H3 Instrucciones De Uso Originales página 18

English
3 Technical Specification
Model
Supply voltage (V)
Power frequency (Hz)
Power input (W)
Speed under load (rpm)
1st speed gear
2nd speed gear
Idle speed (rpm)
1st speed gear
2nd speed gear
Number of impacts (ipm)
1st speed gear
2nd speed gear
Speed pre-selection
Right-left turning
Extent of chuck dia� (mm)
Thread on spindle
Inner hexagon in spindle
Drilling dia� max (mm)
into steel
into aluminium
into wood
into concrete
Clamping neck dia� (mm)
Weight (kg)
Protection class
4 Machine Description
[1]�����Chuck with ring gear
[2]�����Spots on spindle
[3]�����Clamping neck
[4]�����Lever for impact shifting
[5]�����Air vents
[6]�����Stop bar
[7]�����Additional handle
[8]�����Gear-shifting lever (EV 13 E-2H3, EVP 13 E-2H3)
[9]�����Alteration switch lever (EVP 13 E-2H3)
[10] ��Speed pre-selection wheel
[11] ��Switch / controller
[12] ��Latching pin
[16] ��Chuck hook
[17] ��Spanner*
[18] ��Socket screw wrench*
[19] ��Quick-tightening chuck
*) Some accessories displayed or described here may not be
included in the delivery.
5 Double insulation
To ensure maximum safety of the user, our tools are designed and
built to satisfy applicable European standards (EN standards)� Tools
with double insulation are marked by the international symbol of
a double square� These tools must not be grounded and a two-wire
cable is sufficient to supply them with power� Tools are shielded in
accordance with EN 55014�
18
EV 13 F-H3 EV 13 E-2H3
230
50–60
650
0–2 275
û 0–1 730
0–4 000 0–1 100
û
0–3 000
û
û


1�5–13
1/2"–20 UNF 1/2"–20 UNF
û
13
16
25
û
43
1�5
II /
6 Use
EV 13 F-H3; EV 13 E-2H3; EVP 13 E-2H3:
The machine is intended drilling in wood, metal, ceramic and plas-
tic� Machines with electronic control and right/left rotation are also
suitable for screwing and thread cutting (Only for soft screwdriving
applications)�
EVP 13 E-2H3:
The machine is intended for impact drilling in brick, concrete and
stone as well as for drilling in wood, metal, ceramics and plastics�
Machines with electronic control and right/left rotation are also
suitable for screwing and thread-cutting�
The user bears full responsibility for the consequences of using the
tool for purposes other than the above�
7 Commissioning
Any unauthorised use might cause damage to the tool� Therefore
follow these instructions:
– Always use sharp drill bits�
– Load the tool to avoid any significant reduction of speed or
stoppage�
– Always change the speed gear when the machine is idle or at
the machine slow-down at low speed, in no case during the
drilling or when the machine is otherwise loaded�
Check that the information on the production plate matches the
real voltage of the power source�
Check that plug matches the type of socket�
Tools designed for 230 V can also be connected to 220/240 V�
ATTENTION!
Noise is generated during work!
Use ear protection!
EVP 13 E-2H3
230 230
50–60 50–60
650 650
0–630 0–630
0–1 730
0–1 100
0–3 000
û 0–12 600
û 0–34 600
 
 
1�5–13 1�5–13
1/2"–20 UNF
1/4" 1/4"
13 13
16 16
35 35
û 16
43 43
1�7 1�8
II / II /