Descargar Imprimir esta página

Eurocave Compact 59 Serie Modo De Empleo página 14

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 29
4/ INSTALLING YOUR WINE CABINET
Precautions
Do not place your cabinet in an area likely to be flooded.
Do not position your cabinet near to a source of heat or expose it to
the effects of direct sunlight.
Prevent water from splashing on the entire rear section of the appliance.
Position your appliance so that there is a minimum space of 5 – 10 cm
between the wall and the rear wall of your cabinet.
If you are positioning your
cabinet under a work
surface, leave a minimum
space of 5 cm all around the
appliance including under
the work surface. Allow for
a ventilation grill on the
w o r k
s u r f a c e
(recommended).
Install the carbon filter,
which you will find inside
your cabinet's "accessories"
packet, by placing it in the
air circulation hole located inside the cabinet on the top left hand side
(see diagram below).
Arrange the power lead so that it is accessible and does not come into
contact with any component of the appliance.
Slightly tilt the cabinet backwards to adjust the front feet (adjusted by
screwing or unscrewing), so that you can level your cabinet (use of a
spirit level is recommended).
For single-temperature models only:
- If you notice low humidity levels (<55%) a few days after setting your
wine cabinet into operation, we recommend that you use the humidity
cartridge, supplied in a bag with the appliance. Place it at the bottom
of the cabinet, under the rack in the drip tray provided (see diagram
below).
- When using for the first time, completely immerse your cartridge in tap
water for a few minutes to saturate it then allow it to dry. Depending
on external conditions, it may be necessary to add a 10cl glass of water
after several months.
Never obstruct the front ventilation grid.
Beware: any changing of the control panel LED should only be
carried out by a qualified electrician.
8
GB
Fitting the handle
(Full Glass door only on models S-059V3, V-059V3,
S-259V3, V-259V3)
Unscrew the three screws placed on the side of the door, using the Allen
wrench, which you will find in the handle's box.
Fig.1
Position the handle on the specially designed groove on the door frame
(figure 2).
Insert the handle all the way into the groove using a forward movement
Revissez les trois vis (figure 3).
Screw the three screws back on (figure 3).
Fig.1
Take care not to catch the seal when screwing.
Note: adjustment of the handle is possible thanks to the oblong holes.
Fig.2
View from above
Seal
Handle
Front
Door frame
Fig.3
Figure 1
Fig.2
Figure 2
Figure 3
Note : Un Install the stop (which is located in the accessories bag) at the
Fig.3
back of the cabinet (on models S-259V3, V-259V3) / see diagram).
This allows a space of 7 cm to be maintained
between the wall and the rear of the cabinet.
This space allows your cabinet's power
consumption to be optimised.
Place the 2 caps in the 2 holes at the top of
the cabinet.
Do not push the caps all the way in, in order
to allow the rear stop to be installed.
Slide the rear stop between the caps and the
wall of the cabinet, then push the 2 caps all
the way in.
Installation of two cabinets side by side
Caution: In the case of two side by side cabinets installed in extreme
conditions (Temperature >30°C - Relative Humidity > 70%), in order to
prevent condensation of stagnant air between the walls, please leave either
a minimum space of 5 cm between the two cabinets, or fill the space with
a foam sheet to remove the void.
4/ INSTALLING YOUR WINE CABINET
Wall fixing of the cabinet
For large models, if the wine cabinet is not being built in, it is essential
to secure it to the wall to prevent it from tipping forward. You will find
all the necessary parts in the accessories bag supplied with the unit. For
installation (see diagram below):
1
A
Loosen the screws
.
2
B
A
Attach the bracket
to the cabinet with the screws
.
3
C
B
Clip the nut
to this bracket
(preferably choose the hole nearest
to the cabinet).
Warning: make sure that the part is correctly clipped by
pulling upwards by hand. The clip must not come out.
4
D
Preposition the wall bracket
(on the nut to determine the position
for drilling the holes for the wall-mounting screws,
5
D
Drill the holes then attach the wall bracket
with suitable screws
Warning: ensure that the wall fixing can withstand a tensile
force of 100 kg.
6
G
F
Tighten screw
with the washer
until it is screwed fully in and
D
C
there is contact between the wall bracket
and the nut
Only full tightening of the screw will ensure correct fixing of the unit.
Repeat the installation on the other side of the cabinet.
G
F
C
D
A
B
E
1. Building in
A
B
C
A
C
Hinge without pin
Pillar (model 059 only)
B
D
Flush fitting hinge
No. 25 Torx screw
Dimensions for solid, glass or full glass door:
A maxi
A mini
B
059
834
818
Solid door
Glass door
Full glass
259
1794
1778
Solid door
Glass door
Full glass
259 :
It is essential that the unit inside which the cabinet will be fitted
has an opening at the top, at the back, measuring at least 540mm in length
and 50mm in width (see technical door diagram).
E
.
560 min.
C
594
.
600 min.
Dimensions for a technical door:
059
A maxi
852
A mini
836
B
555
C mini
841
C
D
A
x6
C mini
555
823
555
555
572
1783
595
595
B
A
259
1812
1796
595
1801
B
9
GB

Publicidad

loading