Stiga A 1500 Manual De Instrucciones página 11

CAUTION:
Danger of dust in the eyes.
Use safety glasses to avoid the danger of
dust in the eyes.
ELECTRICAL HAZARD:
Connect the power supply only at the end of
all the installation operations. If necessary
during the installation, turn off the general
power supply.
2.3.1. CHARGING BASE INSTALLATION
The charging base can be installed inside the work area or
in an area connected to it by a transition route.
1. Check the installation requirements as indicated in par.
2.1.2.
2. If necessary, prepare the ground so that the surface of the
charging base (Fig. 7.L) is at the same level as the lawn,
the ground must be perfectly flat and compact in order
to avoid deformation of the surface of the charging base.
3. Fix the charging base (Fig. 7 L) to the ground with the
fixing screws (Fig. 7.M).
4. Check that the satellite reference station connector (Fig.
7.A ) is connected to the charging base.
5. Connect the power supply unit to the charging base and
screw in the connector.
6. Connect the power supply plug to the electrical outlet.
7. Make sure that when the robot lawn mower is not in the
charging base, the warning light on the charging base
(Fig. 7.N) is lit (see Par. 3.3)
2.3.2. INSTALLING THE SATELLITE REFERENCE
STATION
The satellite reference station (Fig. 7.A) requires full visibility
of the sky. It is supplied with the charging base and is installed
under the protective cover (Fig. 7.C).
If the charging base (Fig. 7.L) is not placed in an area where
the sky is completely visible, it is necessary to remove the
satellite reference station (Fig. 7.A) from the charging base
and install it in an area where there is full visibility of the sky.
Refer to the Smart User Manual for instructions on the separate
installation of the satellite reference station.
CAUTION:
For safety reasons, the satellite reference
station must never be moved after the
programming of the virtual perimeters,
transition routes and areas to be avoided. The
robot lawn mower could exit the programmed
work area. If the reference station is moved,
the programming must be repeated.
2.3.3. CHARGING THE ROBOT LAWN MOWER AFTER
INSTALLATION
Recharge the batteries for at least 2 hours before using the
product for the first time.
2.4. PROGRAMMING VIRTUAL PERIMETERS,
TRANSITION ROUTES AND AREAS TO BE
AVOIDED
The programming of the virtual perimeters, transition routes
and areas to be avoided is performed using the respective
"STIGA.GO APP" wizards. The procedure requires you to
guide the robot lawn mower manually by walking alongside
EN
it according to the general instructions provided in Par. 2.2.
CAUTION:
The operating area or transition routes used
by the machine must be set so as not to
include public spaces, areas usually used
for parking, transit of vehicles or pedestrian
routes to avoid damage to persons, property
or vehicle accidents.
CAUTION:
For your own safety and to prevent damage to
persons, animals or things, the operator must
already be acquainted with the area in which
the robot lawn mower is manually guided.
When guiding the robot, walk carefully to
avoid tripping.
CAUTION:
The operating area and more generally the
area in which the robot lawn mower can travel
must be cordoned off by fencing.
Make the fence suitable or supervise the robot
lawn mower during its operation.
3. OPERATION
3.1. MANUAL FUNCTIONING OF THE ROBOT
LAWN MOWER
The robot lawn mower can also be used without using the
work schedule programme. In this mode the robot lawn mower
carries out a work cycle, returns to the charging base and
remains there until the next manual start.
In order to use the machine in this mode, it is still however
necessary to programme the virtual perimeters, transition
routes and areas to be avoided. (See par. 2.4)
1. Place the robot mower on the charging base or within the
perimeter of the installation.
2. Press the "STOP" push button (Fig. 1.A) to open the cover
(Fig. 1.B) and access the control panel (Fig. 1.C).
3. Press the "ON/OFF" push button (Fig. 1.E) for 5 seconds
to switch on the robot lawn mower.
4. Press the "SELECT MODE'"push button (Fig. 1.F) until
only the "SINGLE WORK CYCLE" is flashing (Fig. 1.L).
5. Press the "CONFIRM" push button (Fig. 1.G). The icon
(Fig. 1.L) is lit with a fixed light to confirm the operation.
6. Close the cover (Fig. 1.B). The robot lawn mower will
start operating.
NOTE: this mode may not guarantee adequate coverage
of the garden, both in terms of time required and in
terms of uniformity of the cutting result, especially if the
garden has an irregular shape. To achieve the maximum
efficiency of the robot lawn mower, it is recommended to
programme the work schedule .
3.2. DESCRIPTION OF THE CONTROLS ON THE
ROBOT LAWN MOWER
List of controls, indicators and their function:
• Press the "STOP" push button (Fig. 1.A): it is used to stop
the robot lawn mower safely.
• "SAFETY KEY" (Fig. 1.D): it is used to stop the robot lawn
mower safely.
• The "ON/OFF" push button (Fig. 1.E): is used to turn the
robot lawn mower on and off and to reset the alarms.
• "SELECT MODE" push button (Fig. 1.F): it is used to select
4