Siemens SINUMERIK 802D sl Manual De Instrucciones página 15

41130, 5–121
41130 |JOG_ROT_AX_SET_VELO, 3–65
41200, 5–122
41200 |JOG_SPIND_SET_VELO, 3–65
41500 |SW_CAM_MINUS_POS_TAB_1, 3–65
41501 |SW_CAM_PLUS_POS_TAB_1, 3–65
41520 |SW_CAM_MINUS_TIME_TAB_1, 3–66
41521 |SW_CAM_PLUS_TIME_TAB_1, 3–66
42000, 5–123
42000 |THREAD_START_ANGLE, 3–67
42010, 5–123
42010 |THREAD_RAMP_DISP, 3–67
42100, 5–123
42100 |DRY_RUN_FEED, 3–67
42101 |DRY_RUN_FEED_MODE, 3–67
42110, 5–124
42110 |DEFAULT_FEED, 3–67
42120 |APPROACH_FEED, 3–67
42140 |DEFAULT_SCALE_FACTOR_P, 3–67
42150 |DEFAULT_ROT_FACTOR_R, 3–67
42160 |EXTERN_FIXED_FEEDRATE_F1_F9, 3–67
42162 |EXTERN_DOUBLE_TURRET_DIST, 3–68
42200 |SINGLEBLOCK2_STOPRE, 3–68
42400 |PUNCH_DWELLTIME, 3–68
42402 |NIBPUNCH_PRE_START_TIME, 3–68
42404 |MINTIME_BETWEEN_STROKES, 3–68
42440 |FRAME_OFFSET_INCR_PROG, 3–68
42442 |TOOL_OFFSET_INCR_PROG, 3–68
42444 |TARGET_BLOCK_INCR_PROG, 3–68
42450 |CONTPREC, 3–68
42465 |SMOOTH_CONTUR_TOL, 3–68
42470 |CRIT_SPLINE_ANGLE, 3–68
42471 |MIN_CURV_RADIUS, 3–68
42475 |COMPRESS_CONTUR_TOL, 3–69
42480 |STOP_CUTCOM_STOPRE, 3–69
42490 |CUTCOM_G40_STOPRE, 3–69
SINUMERIK 802D sl Listas (LIS), Edición 02/2006
6FC5397–5CP10–0EA0
Índice de los datos de máquina/operador
42494 |CUTCOM_ACT_DEACT_CTRL, 3–69
42496 |CUTCOM_CLSD_CONT, 3–69
42500 |SD_MAX_PATH_ACCEL, 3–69
42502 |IS_SD_MAX_PATH_ACCEL, 3–69
42510 |SD_MAX_PATH_JERK, 3–69
42512 |IS_SD_MAX_PATH_JERK, 3–69
42520 |CORNER_SLOWDOWN_START, 3–69
42522 |CORNER_SLOWDOWN_END, 3–69
42524 |CORNER_SLOWDOWN_OVR, 3–69
42526 |CORNER_SLOWDOWN_CRIT, 3–69
42528 |CUTCOM_DECEL_LIMIT, 3–70
42940, 5–124
42940 |TOOL_LENGTH_CONST, 3–70
42950, 5–124
42950 |TOOL_LENGTH_TYPE, 3–70
42990 |MAX_BLOCKS_IN_IPOBUFFER, 3–70
42995 |CONE_ANGLE, 3–70
43120 |DEFAULT_SCALE_FACTOR_AXIS, 3–71
43200 |SPIND_S, 3–71
43202 |SPIND_CONSTCUT_S, 3–71
43206 |SPIND_SPEED_TYPE, 3–71
43210, 5–125
43210 |SPIND_MIN_VELO_G25, 3–71
43220, 5–125
43220 |SPIND_MAX_VELO_G26, 3–71
43230, 5–125
43230 |SPIND_MAX_VELO_LIMS, 3–71
43240 |M19_SPOS, 3–71
43250 |M19_SPOSMODE, 3–71
43400, 5–126
43400 |WORKAREA_PLUS_ENABLE, 3–71
43410, 5–126
43410 |WORKAREA_MINUS_ENABLE, 3–72
43420, 5–126
43420 |WORKAREA_LIMIT_PLUS, 3–72
43430, 5–126
xv