Cooper Lighting Solutions HALO AL6501LED Manual De Instrucciones

AL6501LED
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Adjustable wrench or ratchet wrench with 10mm socket
• Drill with 3/16 in. drill bit
• 1/2 in. diameter flexible conduit (if applicable, length depends on application)
• 1/2 in. watertight conduit connectors (if applicable)
• Wire connectors
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the
following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Edges may cut. Handle with care.
• Connect fixture to a 120 Volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or
by a qualified electrician. The electrical system, and the method of electrically
connecting the fixture to it, must be in accordance with the National Electrical
Code and local building codes.
• Upside down installation can result in overheating or accumulation of water in
fixture. Install right side up.
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following
2 conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@cooperlighting.com
PACKAGING CONTENTS /CONTENU DE L'EMBALLAGE/CONTENIDO DEL PAQUETE
A. Fixture housing with light sensor
Boîtier du luminaire avec détecteur
de lumière
Alojamiento del accesorio con
detector de luz
E. (2) 1/4-20-1/2" Access cover mounting
screws (attached to fixture)
(2) 1/4-20-1/2 po Vis de montage du
cache d'accès (attached to fixture)
(2) 1/4-20-1/2 plug Tornillos de la cubierta
de acceso (conectado al accesorio)
Instruction Manual / Manuel d'instructions/ Instrucciones
B. One-piece lens assembly
Ensemble de lentille d'une seule pièce
Ensamblado del lente de una sola pieza
F. (4) 8-32 1/4" Lens assembly
lock screws
(4) 8-32 1/4 po Vis de blocage
pour assem blage lentille
(4) 8-32 1/4 plug Tornillos de
fijación del ensamblado del lente
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off an on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void the user's
authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing or
servicing.
NOTE: This fixture is intended to be conduit
connected to a properly installed and properly
grounded metal weatherproof junction box (not
included). All conduit connectors, conduit, and
junction boxes (sold separately) should be cULus
Listed suitable for wet locations.
1. Turn off the power at the main fuse/breaker box.
2. Using the pattern on the box, mark and drill holes for mounting.
NOTE: Mount this fixture in an upright and level position.
3. Install the two bottom mounting screws (D) first, leaving enough room between the
mounting screws and the mounting surface to accommodate mounting the fixture.
4. Screw the top mounting screw (D) into the predrilled hole and back the screw out.
This will leave the hole threaded and make installation of the fixture easier.
5. Remove the cover plate by loosening the two mounting screws (E) inside the
cover plate.
6. Remove access cover (C) from fixture (A). Install the first conduit connector and
conduit (sold separately) into the access cover (C) (Fig. 1).
7. Feed supply wires into conduit. Attach ground wire that is attached to fixture
housing (A) to the junction box earth ground wire.
8. Connect the black fixture wire to the black supply wire (hot) with UL-approved wire
connector (G). Connect the white fixture wire to the white supply wire (neutral) with
UL-approved wire connector (G).
NOTE: Be careful to connect the wires correctly. Make sure no bare strands of wire
extend from the wire nut or other approved wire connectors (G).
9. Place the fixture (A) on the two lower mounting screws (D) and install the upper
mounting screw (D). Tighten all mounting screws to secure the fixture (A).
1
C. Access cover D. (3) ST dia. 0.24*L1.97"
Cache d'accès
Cubierta de acceso
G. (3) Wire connectors H. Pole mounting clamp
(3) Capuchons de connexion
(3) Conectores de cables
A
Conduit
connector
Mounting screws
(3) ST dia. 0.24*L1.97 po
Vis de montage
(3) ST dia. 0.24*L1.97 pulg
Tornillos de montaje
Patte pour montage
sur bras
Abrazadera para
montaje de poste
Fig. 1
Conduit
Junction
box