Giandel PS-1000PDR Manual De Instrucciones página 4

English
2) Output Panel
LED Power
LED Protect
Indicator
Indicator
Power ON/OFF Switch
POWER
POWER
Grounding
3) Remote Controller Box
Power Switch
Backlight Switch
Connecting Wire
E. ASSEMBLE
1) The position of mounting
First ensure that there is enough space to install the inverter, while the installation location must meet
the following requirements:
(1) Drying: Do not use water or other liquids dripping on the inverter.
(2) Cool: a working environment temperature of the product is 32 ~104°F, preferably a temperature of
50~77°F, at a temperature as low as possible within this range.
(3) Ventilation: There should be a certain distance between inverter and other objects, to avoid blocking
the products vents.
(4) Clean: Do not install the products in the dusty, wood chips or other particles. If cooling fan is on, the
particles involved in the inside of the product, thus affecting the normal work.
(5) Inverters and batteries when connected, will produce arcs or sparks, so there should not be around
flammable objects such as gasoline, alcohol, etc.
2) Assemble the inverter
For this big power inverter, which has a heavier weight, preferably mount it on a solid platform, such as
floor, table or mounting bracket fine. In order to avoid falling off, platform for supporting the product
should can bear the weight of sufficient capacity, and it is good with four screws to secure the product.
3
Remote Controller Interface
USB Ports
PROTECT
USB
AC Output Socket
LCD Display
3) Assemble the remote controller box
(1) Fix the remote box on flat surface where a hole should be made, and use 2 screws to fix it through the
two mounting holes on the remote controller.
(2) Hang the remote on the fixing screws.
(3) Connect the remote box and inverter with the wire.
Note: In case not connect to the remote controller, the inverter can be also used as a normal pure sine
wave inverter, turned on by the power switch on the item.
①
③
②
F. BATTERY
1) Current and voltage
The battery is designed to supply the unit with DC input voltage and the rated voltage should be in
accordance with the rated input voltage of the inverter. Any voltage exceeds the range of the input
voltage of the inverter will cause over voltage or under voltage protection.
In the meantime, the battery should supply sufficient current. The small capacity battery cannot drive
the large power electrical appliance. In this case, the battery will be in under voltage protection because
of the over-discharge of the battery.
The simple calculation method of battery current is: load power divided by battery voltage. Due to the
consumption of the inverter itself, the actual current will be about 10% larger. For example, the voltage of
battery is 12VDC, and load power is 1000W, therefore, the actual current of the battery is about
1000W÷12V×110%≈91.6A.
2) Battery operating time
Battery operating time depends on battery capacity and current, and the calculation formula of
operating time is: battery capacity÷current=battery capacity÷(the load power÷battery voltage×110%). For
example, battery specification is 12V, 2000Ah, load power is 1000W, so the total discharging time is
2000Ah÷(1000÷12×110%)≈21.8 hours.
Note: The result of formula above is on the basic of discharging rate of 20 hours of the battery, that is, the
result is from the discharging current of 2000Ah battery not exceed 100A. When the charging current
exceeds this value, the discharging period will reduce. And the quantity of the electricity of the battery
may also influence the result. Please refer to the specification of the battery manufacturer.
G. CONNECTION
1) Grounding
The power inverter has a terminal on the rear panel marked " Grounding "or "
connect the chassis of the power inverter to the ground. The ground terminal has already connected to
the ground wire of AC output receptacle through the internal connecting wire.
The ground terminal must be connected to the ground wire, which depends on where the power
inverter is installed. In a vehicle, connect the ground terminal to the chassis of the vehicle. In a boat,
connect it to the boat's grounding systems. In a fixed location, connect the ground terminal to earth.
Warning:
● To make sure the firmness of the connection. The ground wire must be 14AWG (2.08mm
larger.
● Do not operate the power inverter without connecting to the ground. Electric shock may be resulted.
English
①
". This is used to
2
) or even
4