Moni ASTON Instrucciones De Uso página 13

•
Keep out of fire !
•
Dо not store the product in humid places and in direct sunlight.
•
Do not try to repair the car seat by yourselves. this may led to resulting damage, if it is not done by a professional.
•
DO NOT use on the vehicle seats that face the sides or rear of the vehicle (1a, 1b). Use the child safety seat only on
the vehicle seats that face forward. According to accidents statistics, children are safer when properly restrained in
the rear seating positions than in the front seating positions (1c, 1d).
IMPORTANT! The diagrams and figures in this instruction are illustrative and indicative only.
MAIN PARTS OF THE CAR SEAT: Front side:1. Headrest; 2. Backrest; 3. Harness; 4. Chest pad; 5. Seat cushion; 6. Harness adjuster
strap; 7. Harness. Rear Side: 1. Height adjuster; 2. Harness; 3. Adult belt route slots; 4. Harness connector.
The headrest has 10 levels of height adjustment. Pull the regulator outwards along the direction of arrow, then adjust
it by moving it up and down.
The perforation heights of backrest and headrest should be the same.
Step 1: Turn child safety car seat to the opposite side, retreat the connecting steel of shoulder harness from shoulder
harness according to the above figure; retreat two shoulder harnesses from the splayed hook piece under the back of
safety seat. Step 2: Pull shoulder harnesses from the shoulder harness hole of seat, then take shoulder harnesses
down. Step 3: Plug shoulder harnesses into the appropriate shoulder harness holes in front, connect the shoulder
harnesses on the back of seat to the connecting steel of shoulder harness, and install shoulder harnesses in the splayed
hook piece below. Please ensure that shoulder belt enters shoulder belt hole properly and is not twisted. At the same
time, ensure shoulder belt totally enters the splayed hook piece (as shown in the following figure).
Tightening the safety belt: Pull the shoulder belts up to tighten the loose safety belt near legs. Then, pull the front
drawstring to tighten the safety belt. Try to tighten the safety belt under the precondition of ensuring the comfort of
child.The safety belt near legs should lower as much as possible and should be close to the crotch rather than the
stomach.The loose safety belt is dangerous. So, check whether safety belt regulator can be used normally before
putting your child in the safety, then tighten the safety belt.
Releasing the safety belt: The safety belt can be released by pressing the regulator in the front of seat (under the cloth
cover of seat). The safety belt can be loosened by pressing the regulator and pulling the two shoulder belts towards
the child
The shoulder harness should be passed by the shoulder harness slot the same or slightly higher than the child's
shoulders. Check whether the height of shoulder harness is suitable for children. The shoulder harness should be
passed by the shoulder harness slot the same or slightly higher than the child's shoulders. Step 1: put the two tongues
of buckle together. Step 2: plug the two tongues of buckle into the groove of buckle. If the sound of "click" is heard,
that indicates the buckle is locked. Step 3: pull the shoulder harness up and check whether buckle is locked correctly
If you want to release the safety belt, press the red button of buckle, then the tongues of buckle will automatically
pop out.
Installing the child safety car seat with 3-piont seat belt when forward facing (group I, weight: 9-18kg, from 9
months to 4 years old).
1.Pull the seat belt out, plug the upper terminal into the gap of the headrest and backrest.
2. The belt bottom bypasses the crescent shaped handrail.
3. And then bypasses the Backrest
4. Plug the belt into the slot. That is all.
5. As shown in the figure, lock the lap-belt in the front of car under the handrail at the same side, then plug it into
the groove of lap-belt leaving a sound of click. Check whether it is locked properly by pulling the safety belt up.
MAIN PARTS OF THE CAR SEAT - PD
HEADREAST ADJUSTMENT – FIGURE B
ADJUSTING THE HEIGHT OF SHOULDER HARNESS – FIGURE C
ADJUSTING THE LENGTH OF THE SAFETY BELT – FIGURE D
ADJUSTING AND USING OF THE SAFETY BELT – FIGURE E
CHILD SEAT INSTALLATION: GROUP I (9-18 kg) - FIGURE F
CHILD SEAT INSTALLATION: GROUP II (15-25 kg) – FIGURE G
13