Publicidad
Idiomas disponibles
Idiomas disponibles
Programming of opening limit switch of the
rolling shutter
To set the opening limit switch on a rolling shutter with a
blockage at the top, you must have a previously stored
transmitter available and must proceed with the following points.
1. Power only the motor to be programmed
2. Activate MAMMOLO programming by holding down buttons
4 and 6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 14
The two highlighted digits indicate the remote control channel
recorded in the control unit; for channel 1 the digits are 11,
for channel 2 the digits are 12, for channel 3 the digits are
13, etc up to channel 6. Once the codes have been entered,
the LED of the selected channel will blink for 2 minutes after
which it exits programming.
4. Position the rolling shutter at mid-height using
UP-STOP-DOWN
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase.
6. Release the key PROG
7. Press the key UP: the rolling shutter goes up at normal speed
8. Once in contact with the upper lock, it stops and memorizes
the position
9. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
To set the opening limit switch on a rolling shutter without
blockage at the top, you must have a previously stored
transmitter available and must proceed with the following points.
Repeat points 1, 2, 3, 4, 5, and 6 described above
7. Position the rolling shutter in the UPPER position desired using
the UP and DOWN buttons. To regulate it precisely, press the
PROG button when the motor is close to the limit switch. the
motor will start to move in jerks
8. Press the key STOP once reached the required position
9. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
Programming of closing limit switch of
rolling shutter (closed louver blades)
NOTE: you must have a previously stored transmitter available
and must proceed with the following points
1. Power only the motor to be programmed
2. Activate MAMMOLO programming by holding down buttons
4 and 6 until the 6 LEDs turn on
3. Release the buttons and enter the code 12 11 15
The two highlighted digits indicate the remote control channel
recorded in the control unit; for channel 1 the digits are 11,
for channel 2 the digits are 12, for channel 3 the digits are
13, etc up to channel 6. Once the codes have been entered,
the LED of the selected channel will blink for 2 minutes after
which it exits programming.
4. Position the rolling shutter at mid-height using
UP-STOP-DOWN
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase.
6. Release the key PROG
7. Position the rolling shutter in the LOWER position desired
using the UP and DOWN buttons. To regulate it precisely,
press
the PROG button when the motor is close to the limit switch.
The motor will start to move in jerks
8. Press the key STOP once reached the required position
9. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
Programming of opening position of
adjustable louver blades
NOTE: you must have a previously stored transmitter available
and must proceed with the following points
1. Power only the motor to be programmed
2. Position the rolling shutter at mid-height using
UP-STOP-DOWN
3. Activate MAMMOLO programming by holding down buttons
4 and 6 until the 6 LEDs turn on
4. Release the buttons and enter the code 12 11 16
The two highlighted digits indicate the remote control channel
recorded in the control unit; for channel 1 the digits are 11,
for channel 2 the digits are 12, for channel 3 the digits are
13, etc up to channel 6. Once the codes have been entered,
the LED of the selected channel will blink for 2 minutes after
which it exits programming.
5. Using the UP and DOWN buttons, open the louver blades to
the desired position. To perform a precise adjustment press
the PROG button when the motor approaches the desired
position, the motor will begin to move jerkily
6. Press the key STOP once reached the required position: the
motor stops and then proves the correct storage of the
end-of-stroke by moving for 1/2 second first upwards and
then downwards
7. To exit the programming mode, wait for the led to switch off
or press key 1 to exit immediately.
To bring the rolling shutter into the opening position of
the adjustable louver blades press the STOP button for at
least 3 seconds (with the motor stationary): the louver
blades moves until it reaches the tracked position.
19
Publicidad
