Ferroli ENERGY TOP B Serie Instrucciones De Uso, Instalación Y Mantenimiento página 62

2.3 Lighting and turning off
Boiler lighting
Press the On/Off button (detail 14 - fig. 1).
eco
reset
comfort
fig. 4 - Boiler lighting
• For the following 120 seconds the display will show FH which identifies the heating
system air venting cycle.
• During the first 10 seconds the display will also show the software version of the
cards:
A = Display card software version
B = Top boiler shell control unit software version
C = Bottom boiler shell control unit software version (model ENERGY TOP B 160 -
250only)
• Open the gas cock ahead of the boiler.
• When the message FH disappears, the boiler is ready to operate automatically in
case of a room thermostat demand.
Turning the boiler off
Press the button eco/comfort (detail 7 - fig. 1) for 5 seconds.
fig. 5 - Turning the boiler off
When the boiler is turned off, the PCB is still powered.
Domestic hot water (with optional hot water tank installed) and heating operation are dis-
abled. The antifreeze system remains activated.
To relight the boiler, press the button eco/comfort (detail 7 - fig. 1) again for 5 seconds.
The boiler will be immediately ready to operate whenever domestic hot water is drawn
(with optional hot water tank installed) or in case of a room thermostat demand.
To completely disconnect the power to the unit, press the button detail 14 fig. 1.
B
The antifreeze system does not work when the power and/or gas to the unit are
turned off. To avoid damage caused by freezing during long idle periods in win-
ter, it is advisable to drain all water from the boiler, DHW circuit and system; or
drain just the DHW circuit and add a suitable antifreeze to the heating system,
complying with that prescribed in sec. 3.3.
2.4 Adjustments
Summer/Winter Switchover
Press the button detail 6 - fig. 1 for 1 second.
The display activates the Summer symbol detail 10 - fig. 1. The heating function is deac-
tivated, whereas the possible production of domestic hot water (with optional external hot
water tank) remains activated. The antifreeze system remains activated.
To deactivate Summer mode, press the button
62
EN
A
eco
reset
comfort
B C
eco
reset reset
comfort
eco
reset
comfort
eco
reset
comfort
fig. 6
eco
reset
comfort
fig. 7
(detail 6 - fig. 1) again for 1 second.
cod. 3541G011 - Rev. 00 - 07/2015
ENERGY TOP B
Heating temperature adjustment
Use the heating buttons +/- (details 3 and 4 - fig. 1) to adjust the temperature from a min.
of 20°C to a max. of 90°C.
DHW temperature adjustment (with optional hot water tank installed)
Use the DHW buttons (details 1 and 2 - fig. 1) to adjust the temperature from a min. of
eco
comfort
10°C to a max. of 65°C.
Room temperature adjustment (with optional room thermostat)
Using the room thermostat, set the temperature required in the rooms.
Room temperature adjustment (with optional remote timer control)
Using the remote timer control, set the temperature desired in the rooms. The boiler unit
will set the system water according to the required room temperature. For information on
the remote timer control, please refer to its user's manual.
Sliding temperature
When the optional external probe is installed the corresponding symbol (detail 22 - fig. 1)
is activated on the control panel display (detail 5 - fig. 1). The boiler control system works
with "Sliding Temperature". In this mode, the heating system temperature is controlled
according to the outside weather conditions in order to ensure high comfort and energy
saving throughout the year. In particular, as the outside temperature increases, the sys-
tem delivery temperature is decreased according to a specific "compensation curve".
With Sliding Temperature adjustment, the temperature set with the heating buttons (de-
tails 3 and 4 - fig. 1) becomes the maximum system delivery temperature. It is advisable
to set a maximum value to allow system adjustment throughout its useful operating
range.
The boiler must be adjusted at the time of installation by qualified personnel. Adjust-
ments can in any case be made by the user to improve comfort .
Compensation curve and curve offset
Press the reset button (detail 8 - fig. 1) for 5 seconds, to display the actual compensation
curve (fig. 10) which can be modified with the DHW buttons (details 1 and 2 - fig. 1).
Adjust the required curve from 1 to 10 according to the characteristic (fig. 12).
By setting the curve to 0, sliding temperature adjustment is disabled.
Press the heating buttons (details 3 and 4 - fig. 1) to access parallel curve offset
(fig. 13), modifiable with the DHW buttons (details 1 and 2 - fig. 1).
Press the reset button (detail 8 - fig. 1) again for 5 seconds to exit parallel curve adjust-
ment mode.
eco
reset
comfort
fig. 8
eco
reset
comfort
fig. 9
I
eco
reset
comfort
fig. 10 - Compensation curve
eco
reset
comfort
fig. 11 - Curve parallel offset