Publicidad
Idiomas disponibles
Idiomas disponibles
SPECIFIC RULES FOR THE DRILL PRESS
6. DRILLING ACCESSORIES.
• Make sure the drill bit is not damaged before use; only
use undamaged drill bits
• Make sure the drill bit is securely locked in the chuck
before turning ON.
• Make sure the chuck key is removed from the chuck
before turning ON.
• Use clamps or a vise (not included) to secure a
workpiece to the table. This will prevent the workpiece
from rotating with the drill bit.
7. Make sure the table lock is tightened before starting
the drill press.
8. WORKPIECE REQUIREMENTS.
• Only stand workpieces sturdy enough to withstand
the force of the drill bit.
• Inspect the workpiece for imperfections, nails, staples,
etc. before drilling. Never drill stock that has
questionable imperfections or embedded foreign objects.
• Do not drill materials without a flat surface unless a
suitable support is used (clamp or vise).
9. PREVENTING ACCIDENTAL STARTING. Make sure the
power switch is in the OFF position prior to plugging in the
machine. Always make sure the power switch is in the OFF
position and the machine is unplugged when doing any
cleaning, assembly, setup operations, or when not in use.
10. Do not operate this tool until it is completely assembled
and installed according to the instructions.
11. Remove scrap pieces and other objects from the table
before turning ON the drill press.
12. DRILLING THE WORKPIECE.
• Allow spindle to reach full speed before drilling
the workpiece.
• Never start the machine with the drill bit pressed
against the workpiece.
• Adjust the table or depth stop to avoid drilling into
the table.
• Set the drill press to the speed that is appropriate
for the material being drilled.
ELECTRICAL INFORMATION
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding
provides the path of least resistance for an electric current
and reduces the risk of electric shock. This tool is equipped
with an electric cord that has an equipment grounding
conductor and a grounding plug. The plug MUST be plugged
into a matching outlet that is properly installed and grounded
in accordance with ALL local codes and ordinances.
1. Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a licensed electrician.
2. Improper connection of the equipment grounding
conductor can result in electric shock. The conductor with
the green insulation (with or without yellow stripes) is the
equipment grounding conductor. If repair or replacement
of the electric cord or plug is necessary, DO NOT connect
the equipment grounding conductor to a live terminal.
13. Do not touch moving pieces. Keep hands away from
the drill bit during operation. If cleaning is necessary, turn
off the machine and use a brush to remove sawdust and
chips instead of your hands.
14. Never perform layout, assembly or set-up work on
the table while the machine is ON.
15. After turning off the drill press, wait until the spindle
comes to a complete stop before touching the workpiece.
Always turn the drill OFF before removing scrap from
the table.
16. Before leaving the machine, always turn OFF and unplug
the machine, remove the drill bit, and clean the table.
Turn Off and unplug the machine before cleaning, making
adjustments or changing drill bits. Accidental start-ups
may occur if the tool is plugged in during an accessory
change or adjustment.
17. CLEANING. Never use solvents to clean plastic parts.
Solvents could dissolve or otherwise damage the material.
Use only a soft damp cloth to clean plastic parts.
18. REPLACEMENTS. Should any component of your drill
press be missing/damaged or fail in any way, shut OFF
the switch and remove the plug from power supply outlet.
Replace the missing, damaged, or failed parts using only
identical replacement parts before resuming operation.
CALIFORNIA PROPOSITION 65 WARNING
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities may contain
chemicals, including lead, known to the State of California to
cause cancer, birth defects, or other reproductive harm. Wash
hands after handling. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other
masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies depending on how often
you do this type of work. To reduce your exposure to these
chemicals, work in a well-ventilated area with approved safety
equipment such as dust masks specially designed to filter out
microscopic particles.
These safety instructions can't possibly warn of every
scenario that may arise with this tool, so always make sure
to stay alert and use common sense during operation.
3. Check with a licensed electrician or service personnel if
you do not completely understand the grounding
instructions or whether the tool is properly grounded.
4. Use only three-wire extension cords that have
three-pronged plugs and outlets that accept the tool's plug
(INSERT CR). Repair or replace a damaged or worn cord
immediately.
CAUTION! In all cases,
make certain the outlet
in question is properly
grounded. If you are not
sure, have a licensed
electrician check
the outlet.
3
Fig. 1
Publicidad
