Publicidad
Idiomas disponibles
Idiomas disponibles
BRUSHING OR GRINDING WHEEL REPLACEMENT
Check the grinding wheel or brush before replacement, do not
use brushes and wheels with dents, cracks, excessively worn or
otherwise damaged.
Disconnect the power tool from power supply.
Ensure that new grinding wheel or brush is characterized by
maximal rotational speed equal to 2850 rpm or more. Notice that
the nut of the left grinding wheel is left-hand threaded and it must
be turned clockwise to unscrew. Nut of the right grinding wheel is
right-hand threaded and it must be turned counter-clockwise to
unscrew.
• Unscrew three fixing screws and remove appropriate disc cover
(4) (fig. G).
• Hold the wheel or brush firmly (wear protective gloves to protect
your hands).
• Unscrew the nut that fixes the grinding wheel and the outer
flange (fig. H and I).
• Remove worn out or damaged brushing or grinding wheel (fig.
K).
• Install new grinding wheel or brush onto the shaft and ensure
that there is a washer between the wheel and flange on each side,
and that the wheel or brush is slide fitted, not clearance fitted.
• Screw the nut that fixes the wheel back on its place.
• Hold brushing or grinding wheels when tightening the nuts.
• Be careful not to damage the shaft thread due to applying
excessive torque.
• Install wheel cover (4) and fix it with three screws.
• Adjust setting of the workrest and eye shield.
• Turn the wheel by hand to ensure it is free to rotate.
• Connect the grinder to mains socket, stand aside, switch on the
grinder and allow it to work at full speed for few minutes.
LIGHT BULB REPLACEMENT
Do not apply excessive force when removing or installing light
bulb, it may cause it to break and cut you. In the working lamp of
the grinder (11) there is a 12V/10W light bulb (car type).
• Unscrew and remove the light bulb screen (fig. L).
• Carefully press the used light bulb in the socket and turn it left,
then remove (fig. M).
• Carefully press new light bulb in the socket and turn it right
until it is fixed in appropriate position.
• Reinstall the light bulb screen.
GREASING
In this grinder, ball bearings filled with grease for the whole
working period are used and the tool does not require any
additional greasing. If the wheels do not rotate freely, the bearings
should be replaced in an authorized service workshop.
CLEANING
Never use any caustic agents, or cleaning agents based on
petrol or alcohol. Protect the grinder against moisture.
• Keep outer surfaces of the grinder clean, remove dust from
places where the dirt accumulates with brush or compressed air.
• Wipe shields and body with damp, soft cloth. You can also use
delicate detergent.
• Wipe eye shields with damp soft cloth, be careful not to scratch
them. You can also use delicate detergent.
TECHNICAL PARAMETERS
RATED PARAMETERS
Parameter
Supply voltage
Power frequency
Rated power
Idle engine speed
Linear speed at idle
Disc / brush diameter
Inner diameter of disc / brush
Disc / brush width
Protection class
Mass
Year of production
59G383 stands for both the type and designation of the
NOISE LEVEL PARAMETERS
Sound pressure level
Sound power level
Information on noise
The level of noise emitted by the device is described by: the level
of the emitted sound pressure Lp
(where K is the measurement uncertainty). The following
information: emitted sound pressure level Lp
Lw
were measured in accordance with EN 62841-1.
A
ENVIRONMENT PROTECTION
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa
with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs,
that all copyrights to this instruction (hereinafter Instruction), including, but not
limited to, text, photographies, schemes, drawings and layout of the instruction,
belong to Grupa Topex exclusively and are protected by laws accordingly to
Copyright and Related Rights Act of 4 February 2004 (ustawa o prawie autorskim
i prawach pokrewnych, Dz. U. 2006 No 90 item 631 with later ammendments).
Copying, processing, publishing, modifications for commercial purposes of the
entire Instruction or its parts without written permission of Grupa Topex are
strictly forbidden and may cause civil and legal liability.
12
Bench grinder 59G383
230 V AC
250W S1 / 370W S2
2980 / min
23.4 m / s
12.7 mm
machine
L
= 78.8 dB (A) K = 3dB (A)
pA
L
= 91.8 dB (A) K = 3dB (A)
WA
and the sound power level Lw
A
sound power level
A,
Do not dispose of electrically powered products
with household wastes, they should be utilized in
proper plants. Obtain information on wastes
utilization from your seller or local authorities.
Used up electric and electronic equipment
contains
substances
active
environment. Unrecycled equipment constitutes a
potential risk for environment and human health.
Value
50 Hz
30 min
150 mm
25 mm
AND
9.5 kg
2021
A
in
natural
Publicidad
