Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
► Check the heater immediately if any of the following oc-
curs:
- The heater does not reach temperature.
- The burner makes popping noise during use (a slight
noise is normal when the burner is extinguished).
- Smell of gas in conjunction with extreme yellow tipping of
the burner flames.
► The LP regulator/hose assembly must be located out of
pathways where people may trip over it or in area where
the hose will not be subject to accidental damage.
► Any guard or other protective device removed for ser-
vicing the heater must be replaced before operating the
heater.
► Adults and children should stay away from high tem-
perature surface to avoid burns or clothing ignition.
► Children should be carefully supervised when they are
in the area of the heater.
► Clothing or other flammable materials should not be
hung on the heater or placed on or near the heater.
► To change the gas cylinder in a amply ventilated area,
away from any ignition source (candle, cigarettes, other
flame producing appliances, ...);
► To check that the regulator seal is correctly fitted and
able to fulfill its function
► To not obstruct the ventilation holes of the cylinder
housing;
► To close the gas supply at the valve of the gas cylinder
or the regulator after use;
► In the event of gas leakage, the appliance shall not be
used or if alight, the gas supply shall be shut off and the ap-
pliance shall be investigated and rectified before it is used
again;
► The recommended frequency of checking the tubing or
the flexible hose (at least once per month and each time
the cylinder is changed). If it shows signs of cracking, split-
ting or other deterioration it shall be exchange for new hose
of the same length and of the equivalent quality;
►►
2. HEATER STAND AND LOCATION
►
► The heater is primarily for outdoor use only. Always en-
sure that adequate fresh air ventilation is provided.
► Always maintain proper clearance to combustible ma-
terials, i.e. top 100 cm and sides 100 cm minimum. FIG. 1
► Heater must be placed on level firm ground.
► Never operate heater in an explosive atmosphere like in
areas where gasoline or other flammable liquids or vapors
are stored.
► To protect heater from strong wind, anchor the base se-
curely to the ground with screws. FIG.2
►►
3. GAS REqUIREMENTS
►
► Use propane or butane gas only.
► The pressure regulator and hose assembly to be used
must conform to local standard codes.
► The installation must conform to local codes, or in the
absence of local codes, with the standard for the storage
and handling of liquid petroleum gases.
► A dented, rusted or damaged propane tank may be haz-
ardous and should be checked by your tank supplier. Nev-
er use a propane tank with a damaged valve connection.
► The propane tank must be arranged to provide for va-
por withdrawal from the operating cylinder.
► Never connect an unregulated propane tank to the
heater.
►►
4. LEAKAGE TEST
►
► Gas connections on the heater are leak tested at the
factory prior to shipment. A complete gas tightness check
must be performed at the installation site due to possible
mishandling in shipment or excessive pressure being ap-
plied to the heater.
► Make a soap solution of one part liquid detergent and
one part water. The soap solution can be applied with a
spray bottle, brush or rag. Soap bubbles will appear in case
of a leak.
► The heater must be checked with a full cylinder.
► Make sure the safety control valve is in the OFF posi-
tion.
► Turn the gas supply ON.
► In case of a leak, turn off the gas supply. Tighten any
leaking fittings, then turn the gas supply on and recheck.
► Never leak test while smoking.
►►
5. OPERATION AND STORAGE
►
► TO TURN ON THE HEATER
1. Turn on the valve on the gas supply cylinder completely.
2. Press and turn the variable control knob and hold for
30 seconds. Chile holding down the variable control knob,
Press the igniter buton several times until the pilot flame
lights. Release the variable control knob after the pilot
flame lights.
Note:
► If a new tank has just been connected, please allow at
least one minute for the air in the gas pipeline to purge out
through the pilot hole.
► When lighting the pilot flame make sure that the variable
control knob is continuously pressed down while pressing
the igniter button. Variable control knob can be released
after the pilot flame lights.
► Pilot flame can be watched and checked from the small
round window with sliding lid located at the bottom of the
flame screen (to the left or right side of the corner).
► If the pilot flame does not light or it goes out, repeat
step 3.
4. After the pilot flame lights, turn the variable control knob
to maximum position and leave it there for 5 minutes or
more before turning the knob to desired temperarure posi-
tion.
► TO TURN OFF THE HEATER
1. Turn the variable control knob to PILOT position.
2. Press and turn the variable control knob to OFF posi-
tion. FIG. 3
3. Turn off the valve on the gas supply cylinder completely.
► STORAGE
1. Always close the gas valve of the gas cylinder after use
or in case of a disturbance.
2. Remove the pressure controller and the hose.
3. Check the tightness of the gas valve and for damage. If
you suspect a damage, have it changed by your gas deal-
er.
4. Never store liquid gas cylinder in a sub-terrain or at
places without adequate air ventilation.
BG
BY
CZ
EE
HR
HU
LT
LV
RO
GB
SI
SK
UA
SE
SI
SK
Publicidad
Tabla de contenido
