Atlas Copco LBB16 EP024 Manual De Instrucciones página 5

LBB16 EP024
This can be prevented by flushing with oil (a few drops), run-
ning the tool for 5–10 seconds and absorbing the oil in a
cloth. Protect the tool this way before longer standstills.
Overhaul and lubrication
The tool should be checked regularly at six-monthly inter-
vals. If it is in heavy duty service or not running properly, it
should be taken out of service more often for inspection.
Regarding instruction for dismantling and assembly, see sep-
arate Service Manual.
The throttle valve, planetary gears, needle bearings and ball
bearings must be lubricated with grease when the tool is dis-
mantled for the regular overhauls. Molykote BR2 Plus gives
long intervals between lubrications.
Clean the motor parts and apply a thin layer of air lubri-
cation oil onto the vanes and inner surface of cylinder
and end plates.
Assemble the motor and check that it is running free.
Add two drops of oil through the air inlet and run the
motor (machine) at idling speed for 5-10 seconds.
The strainer in the adapter should be cleaned regularly to pre-
vent choking with resultant decrease in capacity
Lubricating guide for Grinder/Sander (except
turbine) and Drill
General purpose
Brand Bearings
BP Energrease LS-
EP2
Castrol Spheerol EP L2
Esso Beacon EP2
Q8 Rembrandt EP2
Mobil Mobilegrease XHP
222
Shell Alvania EP2
Texaco Multifak EP2
Molycote BR2 Plus
Useful information
Log in to Atlas Copco www.atlascopco.com
You can find information concerning our products, acces-
sories, spare parts and published matters on our website.
Ergonomic guidelines
Consider your workstation as you read through this list of
general ergonomic guidelines and see if you can identify ar-
eas for improvement in posture, component placement, or
work environment.
Air lubrication
Energol E46
Arox EP46
Chopin 46
Almo oil 525
Tonna R32
Aries 32
See "Lubrication"
in
Operating instruc-
tions
© Atlas Copco Industrial Technique AB - 9836 3136 00
• Take frequent breaks and change work positions fre-
quently.
• Adapt the workstation area to your needs and the work
task.
• Adjust for convenient reach range by determining
where parts or tools should be located to avoid static
load.
• Use workstation equipment such as tables and chairs
appropriate for the work task.
• Avoid work positions above shoulder level or with static
holding during assembly operations.
• When working above shoulder level, reduce the load
on the static muscles by reducing the weight of the
tool, using for example torque arms, hose reels or
weight balancers. You can also reduce the load on
the static muscles by holding the tool close to the
body.
• Make sure to take frequent breaks.
• Avoid extreme arm or wrist postures, particularly for
operations requiring a degree of force.
• Adjust for convenient field of vision by minimizing
movement of the eyes and head during the work task.
• Use the appropriate lighting for the work task.
• Select the appropriate tool for the work task.
• Use ear protection equipment in noisy environments.
• Use high-quality inserted tools or consumables to mini-
mize exposure to excessive levels of vibration.
• Minimize exposure to reaction forces.
• When cutting:
A cut-off wheel can get stuck if the wheel is either
bent or if it is not guided properly. Make sure to use
the correct flanges for cut-off wheels and avoid
bending the wheel during cut-off operation.
• When drilling:
The drill might stall when the drill bit breaks
through. Makes sure you use support handles if the
stall torque is too high. The safety standard
ISO11148 part 3 recommends using something to
absorb the reaction torque above 10 Nm for pistol
grip tools and 4 Nm for straight tools.
• When using direct-driven screw or nutrunners:
Reaction forces depend on tool setting and joint
characteristics. The ability to bear reaction forces
depends on the operator's strength and posture.
Adapt the torque setting to the operator's strength
and posture and use a torque arm or reaction bar if
the torque is too high.
• Use dust extraction system or mouth protection mask in
dusty environments.
Country of origin
Please refer to the information on the product label.
Safety Information
5