Craftsman 580.326300 Instrucciones De Uso página 7

Ocultar thumbs Ver también para 580.326300:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Check
Battery
t Attach
Negative
Battery
Wire
The sealed battery on the generator is fully charged
and pre-installed
except for the negative (black)
battery cable.
You will need two 8mm wrenches to install the
negative battery cable.
To install:
.
2.
Cut off tie wrap securing loose end of negative
(black) cable.
Remove nut and washer on negative battery terminal
Nut
_.:::::::" .........
wds her .........
Negative/'
_/
battery
'
/
,,
i
cable
Screw
Positive battery cable
3.
Slide negative battery cable over screw on
negative terminal.
4.
Reattach washer and nut and tighten.
5.
Verify that connections to battery and generator
are tight and secure.
BEFORE
STARTING
THE
Add Engine
OH
NOTE: When adding oil to the engine crankcase, use
only high quality detergent oil rated with API service
classification SF, SG, SH, SJ or higher rated SAE 30
weight. DO NOT use special additives.
1.
Choose a viscosity according to the following table:
STARTING
TEMPERATURE
RANGE
ANTICIPATED
BEFORE
NEXT
O_L CHANGE
* The use of multi-viscosity oils (5W=30, 10W=30, etc.)
in temperatures above 40°F (4°C) will result in higher
than normal oil consumption.
When using a multi=
viscosity oil, check oil more frequently.
** If using SAE 30 oil in temperatures
below 40°F
(4°C), it will result in hard starting and possible engine
bore damage due to inadequate lubrication.
2.
Place generator on a level surface.
3.
Clean area around yellow oil fill cap. Remove oil
fill cap.
4.
Slowly fill engine with oil through oil fill opening
until oil level is to the point of overflowing.
5.
Install yellow oil fill cap and finger tighten securely.
6.
Check engine oil level before starting each time
thereafter. If oil level is below the point of
overflowing, fill to proper level.
NOTE: Check oil often during engine break-in.
Add Fue_
WARNING
WHEN
ADDING
FUEL
Turn
generator
OFF and let it coo! at least 2 minutes
before
removing
fuel cap. Loosen
cap slowly
to relieve
pressure
in tank.
Fill fuel tank outdoors.
DO NOT overfill
tank. Allow
space for fuel expansion.
Keep fuel away from sparks,
open flames,
pilot lights,
heat, and other
ignition
sources.
DO NOT light a cigarette
or smoke.
NOTE: This gasoline engine is certified to operate on
gasoline. Exhaust Emission Control System: EM
(Engine Modifications).
1.
Use clean, fresh, regular UNLEADED fuel with a
minimum of 85 octane with equipment. DO NOT
use fuel which contains Methanol. DO NOT mix oil
with fuel.
2.
Clean area around fuel fill cap, remove cap.
3.
Slowly add regular unleaded fuel to fuel tank. Be
careful not to overfill. Allow about 1.5" of tank
space for fuel expansion, as shown here.
4.
InstaJl fueJ cap and wipe up any spiJJedfuel
CAUTRON! Alcohol-blended
fuels (called gasohol,
ethanol or methanol) can attract moisture, which leads
to separation and formation of acids during storage.
Acidic gas can damage the fuel system of an engine
while in storage.
To avoid engine problems, the fuel system should be
emptied before storage of 30 days or longer. Drain the
fuel tank, start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next season.
See "Storage" on page 16 for additional information.
NEVER use engine or carburetor cleaner products in
the fuel tank as permanent damage may occur.

Publicidad

Tabla de contenido
loading

Tabla de contenido