Ryobi RY36LMX51A Traducción De Las Instrucciones Originales página 5

● before removing the grass catcher or
opening the grass discharge chute cover
● after striking a foreign object; inspect the
product for damage and make repairs
as necessary before restarting and
operating the product
● if the product starts to vibrate abnormally
(check immediately)
– inspect for damage, particularly the
blades
– replace or repair any damaged parts
– check for and tighten any loose parts
■ The cutting blade
approximately parallel to the ground over
which it is being wheeled.
■ The blade on the product is sharp. Use
extreme caution, and wear heavy-duty
gloves when fitting, replacing, cleaning, or
checking bolt security.
■ Never operate the product if the on/off
switch on the handlebar does not properly
start and stop the product.
■ Never attempt to lock the on/off switches in
the on position; this is extremely dangerous.
■ Do not force the product. It will do the job
better and safer at the speed for which it
was designed.
■ Stop the blade when crossing gravel surfaces.
■ Avoid holes, ruts, bumps, rocks, property
stakes, or other hidden objects. Uneven
terrain could cause a slip-and-fall accident.
■ Always ensure that the motor control cable
is never trapped, pinched, or otherwise
damaged during assembly or when folding
the handle.
■ Injuries may be caused, or aggravated, by
prolonged use of the product. When using
the product for prolonged periods, ensure to
take regular breaks.
ADDITIONAL BATTERY SAFETY
WARNINGS
To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never
immerse the tool, battery pack, or charger in
fl uid or allow fl uid to fl ow inside them. Corrosive
or conductive fl uids, such as seawater, certain
industrial chemicals, and bleach or bleach-
containing products, etc., can cause a short
circuit.
PRODUCT FEATURES
OVERLOAD AND OVERHEAT
PROTECTION
The product has an overload protection device.
When overloading is detected, the product
automatically turns off . If the overload protector
is actuated, the on/off bail must be released.
Squeeze the on/off bail, and press the start
button to restart the product. If the product still
does not start, reinstall the battery pack.
The battery pack has overheat protection.
Excessive temperatures will cause the battery
should rotate
to stop powering the product. If the battery
pack is too warm, allow it to cool down before
resuming operation. If the product still does not
work, recharge the battery.
NOTE: The battery pack LED indicator will
not work if the battery protection feature has
caused the battery pack to stop powering the
product. Turn off the product or remove the
battery pack from the product, and the battery
pack LED indicator will resume normal function.
TELESCOPIC HANDLE
The product is equipped with a telescopic
handle that can be adjusted for storage and
operation. The telescopic handle must be fully
extended when setting up the product for use.
NOTE: The product will not function if the
telescopic handle is not fully extended and the
two latches are not in the correct position.
SELF-PROPEL PADDLES
transporting the product from one location to
another. Only engage the blades by pulling the bail
when you are ready to mow. Failure to follow these
instructions can result in serious personal injury.
The product is equipped with self-propel
paddles that activate the self-propel feature.
Squeeze one or both of the paddles to engage
the self-propel feature. To disengage the self-
propel feature, release the paddles.
NOTE: The self-propel paddles can be used
without engaging the blade when moving the
product to another location. Release the paddles
before attempting to re-engage the blade.
CRUISE CONTROL
The cruise control feature can be used to adjust
the speed of the product to accommodate the
user's pace when the self-propel feature is
WARNING! Never engage the blades when
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
5