Publicidad
Idiomas disponibles
Idiomas disponibles
EN
power cable. It is necessary to check the insulation of power cable and extension cable or
ask the manufacturer of the device and/or of the extension cable. If you notice damage to
any part of the equipment, its further use is forbidden. In this case, the device must be sub-
mitted to an authorized service center. The device may be used by children, who are at least
8 years old and by persons with reduced physical and mental capabilities, and by persons
who lack of experience and knowledge of the appliance, it is provided the supervision or
instruction concerning the use of appliance in a safe way, so that the associated risks would
be understood. Children should not play with the device. Children without supervision should
not carry out the cleaning and maintenance of the device.The device designed for domestic
operation only. After the packing of 20 bags the device should be left for 25 minutes. You
should also wait approximately 20 seconds between each packaging. After each use, you
should disconnect the power cable plug from a mains outlet. In the case of thermal overload
the product can automatically turn off . Then you should disconnect the power cable from a
mains outlet and allow the device to cool down.
OPERATION OF THE DEVICE
Vacuum packaging
ATTENTION! During all the preparatory activities, you should disconnect the power cable plug from a mains outlet.
ATTENTION! Pressing of any function button will change the control light, which is placed below.
Raise the cover of device. If the cover is closed by the latch, push the both lock buttons at the same time, to unlock the cover,
and then raise it.
Inside the device there is a safety switch that will let you run the device only when the cover is closed properly. It should not be
pushed when the cover is opened, it is forbidden to block the safety switch.
Bag must be prepared for use in the packaging machine. Use only special bags, intended only for use in vacuum packaging
machines. The bag can be cut by adjusting its size to the product to be packed. Please remember that all the edges of the bag
except one should always been welded, and the trimmed edge was even and not wider than the maximum width of bags listed in
the table. Choosing the bag size, make sure that there remains of at least 5 cm of the bag from edge to the product to be packed.
Put the bag so that it it over heating strip, and its edge, which is designed to be welded, is completely inside the cover seals. The
chamber packaging machine is equipped with retaining plates that facilitate appropriate positioning of the bag. The bag edge
should touch the retaining plate. Align both sides of the bag so as not to create a bends, folds or wrinkles. Close the cover and
make sure that the latch worked out. The cover cannot be raised freely. Connect the device to mains. The control lamp lights up.
Press the "Pakowanie" (Packaging) button, this will start the process of air suction, and when it is complete, the welding of bag
edge. This is indicated by the ignition of control light, which is placed under the button.
After the end of the packing process, the device automatically stops the process of sucking air, that will be indicated by switching
off of the control lam located under the button. Then you should switch off the device from power supply, and unlock the cover
latches by pressing both buttons the tabs. Lift the cover and remove the bag with packed product.
ATTENTION! Heating strip may be hot. You should avoid touching it when you remove the bag from machine.
If, during the process of packing, it will be necessary to interrupt it, press the "Stop" button.
If, in the course of packaging there will be noticed the undesirable deformation of the packed product or liquids, which has been
present in the product, start to be sucked in by the packaging machine, you should press the" Zgrzewanie" (Welding) button, this
will stop the process of air sucking and start welding of the bag edges.
In the case of packaging of delicate products it recommended to use the "Impuls" button. Single pressing of this button will cause
only temporary start of packaging machine and suction of a small amount of air. If you press and hold this button, the device would
start its continuous operation, but button release causes the immediate discontinuation of air suction. This allows you to choose
the degree of air suction in the case of sensitive products.
After the end of suction in pulsed mode, you should weld the bag by pressing the "Zgrzewanie" (Welding) button. The control lamp
O R I G I N A L
I N S T R U C T I O N S
12
Publicidad
