Publicidad
LITHIUM ION BATTERY
IMPORTANT: Products that contain lithium ion batteries are subject to stringent transportation
regulations. If you need to ship this product (with battery included) for service, travel or any other
reason, you must comply with the following shipping instructions.
• Remove lithium ion battery from the product.
• Turn robot over and remove side brush screw and then remove the side brush by pulling gently.
• Unscrew the two screws on bottom cover and lift it.
• Remove battery.
• Place a piece of tape over the battery´s metal charging contacts.
• Reinstall battery in the product (with the tape on it) and secure battery cover.
• Package product in its original packaging or in your own packaging that prevents any movement during
transportation.
• Ship via ground transportation only (no air shipping).
The symbol on the product or its packaging indicates:
Do not discard electronic devices onto unclassified waste, use collections facilities that separate trash. Contact your local authorities to
obtain information regarding the available collection systems. Contact your local or regional residue authorities to obtain more
information regarding collection, reuse and recycling programs.
CAUTION: Charge the Robot Li-Ion Lithium Ion Battery 14.4V, maximum 2,600mAh. Other types of
batteries can explode and cause injury. Always contact Koblenz Customer Service for the correct
replacement of your battery.
ROBOT VACUUM CLEANER ASSEMBLY
1. SIDE BRUSH INSTALLATION
1
2
2. CLEANING AND CHARGING BASE
Clean base
1
Dust bag warehouse
2
Indicator light
Vacuum port
2. Plug in the charging base and route
Contact point
the rest of the cable to the channel on
the bottom of the charging base.
Clean base area
Note: If you do not put the rest of the cable in
the storage space, the Robot Vacuum Cleaner
may get stuck while charging or cleaning.
If the battery runs out before the end of a cleaning cycle, the Robot Vacuum Cleaner will automatically return to the
charging base. If the Robot Vacuum Cleaner cannot access the charging base, it will not be able to recharge, the
device will return to its initial location and end the cleaning cycle, then place the robot manually on the charging
base.
3. CHARGING METHOD
Please keep the adapter plug inserted into household power socket, and adapter round plug into recharge stand
socket. Before using your Robot Vacuum, please charge it to 100% first, your Robot Vacuum Cleaner will have an
autonomy of up to 80 continuous minutes. After fully charged, you are ready to start to use it. Keep the dust
collection clean base cord plug connected to the power outlet.
NOTE: The full charging time (from 0% to 100%) is 5 hours.
MANUALLY:
Turn on battery main switch on Robot Vacuum Cleaner bottom, and manually, match the divice with the recharge
stand for charging.
AUTOMATICALLY:
Robot Vacuum Cleaner returns back to recharge stand when power is low during cleaning. Total charging time is
3
about three to 4 hours (depending on the battery condition before charging).
1. Attach side brushes to the bottom of
Robot vacuum Cleaner by pressing a
brush into each slot.
2. Turn on the main power switch on the
bottom of robot.
3
3. Recharge Stand Position:
Put the charging base back on the wall, make
sure the place is open and clear.
• 2 meter (6.5 feets) in front of the Recharge
Stand
• 1 meter (2.3 feets) on both sides of the
Recharge Stand
CONFIGURACIÓN A SIRI
Antes de configurar su Apiradora Robot a Siri, debe tener descargada la app "Atajos".
Los atajos te ofrecen una forma rápida de realizar acciones con tus apps con un solo toque o al pedirle a Siri alguna tarea.
Disponible en:
LIMPIEZA Y MANTENIMIENTO
IMPORTANTE: Antes de limpiar y darle mantenimiento a su Aspiradora Robot, desconecte la clavija
del adaptador, el interruptor de alimentación principal del equipo debe apagarse para evitar que se
encienda y ocasione algún accidente.
3. En la pantalla, elija su Aspiradora Robot y seleccione las funciones que
desee que sean ejecutadas (modo de aspirado, encender/apagar, nivel de
agua, etc) y guarde los cambios.
4. Regrese a la pantalla para ejecutar tareas y seleccione el botón con 3
puntos en la esquina superior derecha de la pantalla.
5. Cambie el nombre de la tarea (Ejemplo:
"Prende Aspiradora"). Este nombre será el
que active la tarea por comando de voz en
sus dispositivos Alexa, Asistente de Google
y Siri.
1. En la pantalla principal de la app Tuya
Smart seleccione la pestaña "Escena" y
después ir a la opción "Ejecute" en la parte
superior de la pantalla.
En el lado derecho de la pantalla,
seleccione la opción "Añadir a Siri" para
que las tareas previamente creadas puedan
ser activadas por Siri.
2. Se abrirá la app "Atajos". Seleccione los
accesos directos que desee agregar a Siri.
Dando clic al "+". Haga clic en "Listo" para
guardar la tarea y pruebe diciendo la frase
a Siri.
Nota: Su Apiradora Robot no es compatible con
Apple HomeKit.
24
Publicidad
