Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH (
Original Instructions)
that the arrow on the sanding belt (6) points in the same
direction as the arrow on the tool.
♦ To ensure a correct tracking, the sanding belt (6) must
be centred over the rollers.
♦ Push the tension lever (5) inward to tension the sanding
belt (6).
Variable speed control dial (FIG. D)
♦ Adjust the variable speed control dial (7) to increase
or decrease the speed according to the material and
sanding belt specification to be used (also possible
during no load operation).
Fitting and removing the dustbag (FIG. C)
♦ Slide the dustbag (3) over the dust extraction outlet (4).
♦ To remove the dustbag (3), slide it off the outlet.
BEFORE USE
♦ Before using the tool for the first time, it is recommended
to receive practical information.
♦ Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool.
♦ Do not work materials containing asbestos (asbestos is
considered carcinogenic).
♦ Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable.
♦ Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable.
♦ Follow the dust-related national requirements for the
materials you want to work with.
♦ Do not clamp the tool in a vice.
♦ Use completely unrolled and safe extension cords with
a capacity of 16 Amps
AFTER USE
♦ After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it.
USE
WARNING! Always wear gloves when you change
accessories. The exposed metal parts on the tool and
accessory may become extremely hot during operation.
Please operate tool with normal load. Do not overload. Do
not abuse the tool, please refer instruction manual to use
the tool correctly.
WARNING! Let the tool work at its own pace. Do not
overload. The auto tracking feature of this sander allows
you to sand without adjusting the location of the sanding
belt (6).
♦ Make sure that the sanding belt (6) is centred over the
rollers during assembly.
18
♦ During use, if the sanding belt (6) begins to track
incorrectly, remove the belt sander from the work piece
and allow it to run briefly. The sanding belt (6) will return
to its centred position.
♦ If the sanding belt (6) does not return to the centred
position, allow the unit to cool for 5 minutes and repeat.
Switching on and off (FIG. A. FIG. E)
♦ To switch the tool on, press the on/off switch (1).
♦ For continuous operation, press the lock-on button (2)
and release the on/off switch (1).
♦ To switch the tool off, release the on/off switch (1).
♦ To switch the tool off when in continuous operation,
press the on/off switch (1) once more and release it.
Emptying the dust bag
The dustbag (3) should be emptied every 10 minutes.
♦ Unzip the dustbag (3) and empty it before continuing.
Hints for optimum use
♦ Always hold the tool with both hands.
♦ Do not exert too much pressure on the tool.
♦ Regularly check the condition of the sanding belt (6).
Replace when necessary.
♦ Always sand with the grain of the wood.
♦ When sanding new layers of paint before applying
another layer, use extra fine grit.
♦ On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to a
fine grit for a smooth finish.
♦ Consult your retailer for more information on available
accessories.
WARNING! Do not use this tool to mix or pump
easily combustible or explosive fluids (benzine,
alcohol, etc.). Do not mix or stir inflammable liquids
labelled accordingly.
Accessories
The performance of your tool depends on the accessory
used. STANLEY accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best from
your tool.
MAINTENANCE
Your STANLEY corded/cordless appliance/tool has been
designed to operate over a long period of time with a
minimum of maintenance. To ensure satisfactory operations,
the tool must be maintained and cleaned regularly
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing accessories,
before adjusting or changing set-ups or when making
repairs. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
♦ This machine is not user-serviceable. If problems occur
contact an authorised repair agent.
♦ The tool will automatically switch off when the carbon
Publicidad
