Shark S4701D Guia Del Usuario página 8

Using Your Steam Mop - continued
The Shark ® 2-in-1 Blast & Scrub Steam Pocket ® Mop has Intelligent steam settings that allow you to select the right
amount of steam for your floors and produces greater steam for your accessories. See below for tips on when to use
each setting.
SETTING IDEAL FOR THESE SURFACES
Laminate
Hardwood
Marble
Hardwood
Marble
Tile
Stone
Sealed above-floor hard surfaces
around the house
To engage the Scrub Blast Mode, slide the Engage Scrubber/Release Head Button down until
SCRUB BLAST
you hear a click. The Stain Scrubber will automatically pop in to position. Lift the Mop body off
the Mop Head and place the Stain Scrubber on the floor to start scrubbing. You can select your
LO HI
preferred level of steam. Use LO Setting for low-moisture scrubbing. Use the HI Setting for
stubborn, stuck-on stains.
TO SANITIZE* WITH THE RECTANGLE MOP HEAD USING THE SCRUB SIDE OF THE POCKET PAD:
1
Start with a clean Pocket Pad Scrub Side down.
2 Plug in the unit and press the Steam Control Button to select the HI Setting.
3 Wait 30 seconds for the unit to begin producing steam.
4
Start mopping on an appropriate sealed hard-floor surface with a forward and backward motion. After three minutes,
your unit is ready to be used to sanitize.
5
Using a forward and backward motion, move the unit over the area you seek to sanitize. Repeat at least 15 times.
* Sanitization studies were conducted under controlled test conditions. Household conditions and results may vary.
With Rectangle Mop Head, HI Setting only, Scrub Side only (Scrub Side of the pad is the side with the scrubbing
strips as opposed to the side with the shaggy fingers). Not with Above-Floor Accessories or in Blast & Scrub mode.
13 1-800-798-7398
RECOMMENDED USAGE
Cleaning delicate surfaces
Light cleaning and dusting
Loosening and lifting light dirt
Cleaning most surfaces and large areas
Basic, everyday cleaning
Removing spots and smaller messes
Cleaning moderate- and heavy-traffic areas
Sanitizing* floors
Dusting or cleaning above-floor sealed hard surfaces.
Using Your Handheld Steamer
Your Shark Steam Blast 2-in-1 Steam Pocket
®
Mop can be converted to a Handheld Steamer that is
designed to clean surfaces that can withstand high heat
and moisture. Do not use on unsealed wood surfaces
(especially antique wood furniture), unglazed ceramic
tile, painted surfaces, or surfaces that have been
treated with wax, oils, varnishes, or shellac. The sheen
may be removed by the heat, steam, and friction of the
cleaning Accessories. It is always recommended to test
an isolated area of the surface to be cleaned before
proceeding.
We also recommend you check the use and care
instructions from the surface manufacturer.
When cleaning finished wood surfaces, use broad,
continuous strokes. To prevent surface damage, avoid
focusing steam or allowing the cleaning Accessories to
remain stationary in any one spot.
NOTE: To ensure constant steam flow, make sure
the Steam Nozzle is not facing upward.
®
CAUTION: To avoid scalding injuries, always
unplug and allow the Steam Mop to cool before
transitioning it to the Handheld Steamer.
1
To transition the Handheld Steamer, press and hold
down the Handle Release Button while pulling out
the Mop Handle (fig. 9).
2 To remove the Mop Head, press down on the
Engage Scrubber/Release Head Button and lift the
Mop Body off the Mop Head (fig. 10).
NOTE: When you remove the Mop Handle, steam
will automatically stop.
NOTE: Do not leave the wet Mop Head on any floor
for a prolonged period of time.
www.sharkclean.com
EN
fig. 9
fig. 10
14