Gardol GAT-E20Li OA Manual De Instrucciones Original página 22

5.2 Fitting the blade head (Fig. 5 – 6)
Fit the blade head (Item 7) onto the mounting
shaft and fasten it with the screw (Item 14).
5.3 Inserting the blade (Fig. 7)
Place the larger opening of the blade (Item 9) in
the blade mount (A) on the blade head (Item 7)
and pull it outwards in the direction of the arrow
until the blade clicks into place as shown in Fig.
22.
5.4 Height adjustment (Fig. 8)
Undo the union nut (Item 5) until the grass trim-
mer handle can be moved in and out freely. Now
set the required working height (Fig. 9) and se-
cure the handle in this position by tightening the
union nut again.
5.5 Fitting the additional handle (Fig. 10)
Fit the additional handle to the mount provided,
paying attention to the teeth (Item I & II). Then
secure the additional handle with the help of the
screw and the adjustment lock provided. Make
sure that the compartment for the spare blades
faces the top of the equipment.
5.6 Adjusting the additional handle (Fig. 11)
Undo the adjustment lock (Item 3) for the additi-
onal handle until it can be moved forwards and
backwards without any great resistance. Set the
required position and tighten the adjustment lock
again.
5.7 Adjusting the angle of tilt of the guide
handle (Fig. 12)
Press the button for the angle of tilt adjustment
(Item K). Now you can set the long handle to the
required tilt. Release the button and allow the
handle to lock into position to fi x the angle of tilt.
Three diff erent locking angles are possible.
5.8 Installing the battery (Fig. 13/14)
Press the side pushlock buttons of the battery
pack as shown in Fig. 13 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 14, make sure that
the pushlock buttons latch in place! To remove the
battery pack, proceed in reverse order.
5.9 Charging the battery (Fig. 15)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
Anl_GAT_E_20_Li_OA_SPK7.indb 22 Anl_GAT_E_20_Li_OA_SPK7.indb 22
GB
(10) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Insert the battery pack (11) into the battery
charger (10).
4. In section „Charger indicator" you will fi nd a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal. If the battery pack
fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless grass trim-
mer drops. Never fully discharge the battery pack.
This will cause it to develop a defect.
5.10 Battery capacity indicator (Fig. 16)
Press the switch for the battery capacity indicator
(Item C). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
- 22 -
07.09.2016 12:08:37 07.09.2016 12:08:37