Milwaukee 5262-21 Manual Del Operador página 4

SYMBOLOGY
Double Insulated
Volts
Alternating Current
Amps
No Load Revolutions per Minute (RPM)
BPM
Blows per Minute Under Load (BPM)
Read Operator's Manual
UL Listing for Canada and U.S.
C US
Approval Mark for Mexico
FUNCTIONAL DESCRIPTION
4
3
2
1. Side handle
5
2. Clamp
3. Depth gauge rod
1
4. SDS Plus bit holder
5. Mode selector lever
6. Trigger
7. Control switch
8. Handle
ASSEMBLY
To reduce the risk of injury, always
WARNING
unplug tool before changing or
removing accessories. Only use accessories
specifically recommended for this tool. Others
may be hazardous.
Always use a side handle when using this tool.
Always brace or hold securely.
Adjusting the Side Handle Position
1. Loosen the side handle by unscrewing the side
handle grip until the side handle rotates freely.
2. Rotate the side handle to the desired position.
3. Tighten the side handle grip securely.
Setting the Depth Gauge
1. Press in the clamping lever.
2. Slide the depth gauge rod backward or forward
until it is set for the desired depth.
NOTE: The drilling depth is the distance between
the tip of the bit and the tip of the rod.
3. Release the clamping lever.
To reduce the risk of injury, do not
WARNING
grasp the bit while the chuck is
rotating or while the bit is falling from the chuck.
Only use accessories with SDS or SDS Plus shanks.
Be sure that the shank of the bit is clean. Dirt particles
may cause the bit to line up improperly. Do not use
bits larger than the maximum recommended capacity
of the drill because gear damage or motor overload-
ing may result. For best performance, be sure that
the bit is properly sharpened and the shank is lightly
greased before use.
1. Insert the bit or chisel into the nose of the tool.
2. Rotate bit slowly until it aligns with the locking
mechanism.
3. Push bit into tool until it locks.
4. Check that the bit is locked
properly; it should be pos-
sible to pull the bit back and
forth slightly (about 1/4").
5. To remove bits and chisels,
pull bit holder release collar
toward the rear of tool and
remove bit.
NOTE: Use caution when
handling hot bits and chisels.
6 7 WARNING
removing accessories or making adjustments.
Use only specifically recommended accessories.
Others may be hazardous.
Always wear proper eye protection marked to
comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Keep hands and cord away from the bit and all
moving parts.
8
Always use a side handle when using this tool.
Always brace or hold securely.
Cut embedded rebar only if this operation does
not affect the integrity of the building. If in doubt,
consult a structural engineer. Tool operator fully
responsible for adverse structural effects.
These MILWAUKEE Rotary Hammers have three
settings: rotation only, rotary hammer, and hammer
only. Always allow the motor to come to a complete
stop before changing the mode selection to avoid
damage to the tool.
1. For rotation only, press in the
selector release button and
turn the selector lever so the
arrow on the lever points to
the twist drill symbol.
2. For rotary hammering, press
in the selector release button
and turn the selector lever so the arrow points to
the hammer and twist drill
3. For hammering only, press in the selector release
button and turn the selector lever so the arrow
points to the hammer symbol.
4. To freely rotate the bit to the desired angle for ham-
mering only, press in the selector release button
and turn the selector lever to the
follow step 3.
NOTE: To engage the hammering mechanism, main-
tain pressure on the bit. When pressure on the bit is
released, the hammering action will stop.
4
Installing Drill Bits and Chisels
OPERATION
To reduce the risk of injury, always
unplug tool before attaching or
Selecting Action
symbol.
symbol. Then,