Milwaukee M12 SI-0 Manual Original página 8

TECHNICAL DATA
Type
Average Heater Power (max)
Set Tip Temperature
Warm up time
Battery voltage
Weight according EPTA-Procedure 01/2014 (2,0 Ah)
Recommended ambient operating temperature
Recommended battery types
Recommended charger
WARNING
Read these instructions carefully, be
familiar with the controls and the proper use of the machine.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS SOLDERING IRON
Contact with a hot tool tip could ignite fl ammable materials.
Contact with a hot tip could ignite a fi re.
Do not stand or store tool upright on the battery pack. Tool could
tip resulting in contact between hot tip and fl ammable materials.
Always set/store tool on its side when not in use.
Keep hands and fi ngers behind fi nger guard. Serious burns can
occur if skin contacts tip.
Remove battery before storing. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
Work in well ventilated areas. Soldering can produce fumes and
smoke.
Use personal protective equipment when using chemicals, such
as fl ux and solder paste. Follow all manufacturer instructions.
To reduce the risk wear safety goggles or glassesof injury,
always with side shields.
For changing the soldering tip ensure the tip is cool and the tip
temp indicator is off before touching the tip. Serious burns could
occur if skin contacts a hot tip.
Do not stand on battery pack (unstable).
ADDITIONAL SAFETY INSTRUCTIONS
Never allow children, persons with
reduced physical, sensory or mental
capabilities or lack of experience and
knowledge or people unfamiliar with
these instructions to use the machine,
local regulations may restrict the age of
the operator.
Remove the battery pack before
starting any work on the machine.
Do not dispose of used battery packs
in the household refuse or by burning
them. Milwaukee Distributors off er to
retrieve old batteries to protect our
environment.
Do not store the battery pack together
14
M12 SI
Soldering Iron
90 W
400 °C
18 s
12 V
0,41 kg
-18...+50 °C
M12B...
M12...
with metal objects (short circuit risk).
Use only System M12 chargers for
charging System M12 battery packs.
Do not use battery packs from other
systems.
Battery acid may leak from damaged
batteries under extreme load or
extreme temperatures. In case of
contact with battery acid wash it off
immediately with soap and water. In
case of eye contact rinse thoroughly
for at least 10 minutes and immediately
seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or allow a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain
industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The Soldering Iron is intended to be used for soldering or tinning
electrical components, cables, conductors, etc use away from
mains supply.
Do not use this product in any other way as stated for normal
use.
ENGLISH
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Batteries which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and batteries must be kept clean.
For an optimum life-time, the batteries have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery storage longer than 30 days:
Store the battery where the temperature is below 27°C and away
from moisture
Store the battery in a 30% - 50% charged condition
Every six months of storage, charge the battery as normal.
Transport of Li-Ion batteries
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only Milwaukee accessories and Milwaukee spare parts.
Should components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!)
Remove the battery pack before starting any work
on the machine.
Always wear eye protection!
Caution – hot surfaces!
Do not dispose electric tools, batteries/rechargeable
batteries together with household waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible recycling
facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
UK Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 15