Publicidad
Idiomas disponibles
Idiomas disponibles
• The laser on/off switch must be turned on
for the laser line to show.
• This laser guide is powered by two AG13
(1.5V) button cell batteries.
Cutting Line
Blade
Tile
Laser Beam
FIGURE 11
INSERTING AND REPLACING THE
LASER BATTERIES
(see FIGURE 12)
1. Open the cover of the battery box.
2. Place the 2 button cell batteries in before
turning on the laser beam.
FIGURE 12
OPERATION
IMPORTANT: ALWAYS turn off the saw and
remove the plug from the outlet BEFORE
adding or removing accessories and making
adjustments.
FAILURE TO UNPLUG
THE SAW COULD RESULT IN ACCIDENTAL
STARTING CAUSING POSSIBLE SERIOUS
PERSONAL INJURY.
BEFORE STARTING THE SAW
1. Make sure saw is unplugged.
2. Pour water into the tray and fill water level
higher than the pump intake nozzle.
NOTE: ALWAYS keep enough water in the
reservoir when operating the saw. DO NOT
let the saw run dry.
3. IMPORTANT: ALWAYS completely drain
the water reservoir and clean thoroughly
after each use
1. Ensure that the directional arrow marked
on the blade corresponds with the rotation
of the motor.
2. With the saw disconnected from the
power supply, rotate the blade by hand to
ensure it is free from obstruction.
3. Always keep the blade-securing arbor and
collars clean.
4. Ensure that the blade-securing bolt is
securely tightened.
5. NEVER try to cut freehand. Always ensure
that the tile to be cut is pressed firmly
against the rip fence.
6. Ensure the tile that will be cut off has
sufficient room to move sideways. Failure
to do so may result in the off-cut binding
against the blade.
7. NEVER cut more than one tile at a time.
8. NEVER cut pieces so small that it cannot
be held securely against the rip fence, and
provide enough space for the hand to be a
safe distance from the blade.
TOP VIEW
9. Ensure that the table and surrounding area
are clear with the exception of the tile to be
Blade
cut.
10. Before cutting a tile piece, let the saw
blade run freely for a few seconds. If it
makes an unfamiliar sound or vibrates
excessively, switch it off immediately and
disconnect it from the power supply.
Laser Beam
11. Let the blade reach full speed before
starting the cut.
12. Let the blade come to a complete stop
before removing any jammed material from
around the blade area.
13. NEVER allow the blade to run dry. Failure
to keep the water tray at the recommended
level will result in possible over-heating of
the diamond blade.
CAN OCCUR IF OPERATED IMPROPERLY.
• Before turning the tile saw on, verify the
alignment of the cutting table and the
cutting blade. (Always center the cutting
blade in one of the cutting table grooves
before cutting).
• Keep fingers and loose clothing away
from rotating blade.
• Use extreme caution when cutting tile.
Make sure hands and fingers are clear
from the blade groove in the table.
• Electrical shock can occur if operating
instructions are not followed. FOR YOUR
OWN SAFETY READ INSTRUCTION
MANUAL BEFORE OPERATING SAW.
• Wear eye protection.
• Use blade guard for every operation for
which it can be used.
• Unplug saw before servicing, when
changing cutting wheels, and cleaning.
• Use tool only with smooth-edge cutting
wheels free of openings and grooves.
• Replace damaged cutting wheel before
operating.
• Do not fill water tray above water fill line.
TO START THE SAW
1. Plug the saw in to a GFCI (Ground Fault
Circuit Interrupter) protected outlet (see
FIGURE 13).
2. Create "drip loop" in the cord
(see FIGURE 14).
FIGURE 13
PERSONAL INJURY
– 5 –
FIGURE 14
USING THE RIP/ANGLE
GUIDE
The miter scale on the Rip/Angle guide can
be easily read, showing 45° miter angles.
1. Loosen the locking handle to move the
guide along the front rail to the desired
position and handle. (see FIGURE 15)
2. Loosen the locking knob to turn the guide
to the desired angle along the arc slot.
3. Tighten the locking knob.
Locking Knob
FIGURE 15
ADJUSTING THE CUTTING
HEAD
RAISE THE CUTTING HEAD
1. Always turn the saw OFF when raising or
pressing down the cutting head.
2. Loosen the blade elevation locking knob.
(see FIGURE 16)
3. Lift the handle upward to raise the cutting
head.
4. Once the cutting head has been raised
to the desired height, tighten the blade
elevation locking knob to lock.
5. When transporting or storing the tile saw,
the cutting head should always be locked in
the low position.
TILTING THE CUTTING HEAD
1. To tilt the blade for bevel cutting, loosen
the blade tilting locking knob behind the
motor head. (see FIGURE 17)
2. Firmly grasp the handle and tilt the cutting
head by turning the handle clockwise.
3. Tighten the blade tilting locking knob.
Drip
Loop
Publicidad
