EUFY RoboVac 30C Manual Del Propietário página 16

English
Error Tone Cause
• RoboVac's drop sensors are dirty.
Three beeps
• RoboVac is stuck on the ledge of a
staircase and cannot reverse.
Four beeps RoboVac's power level is too low.
Solid red indicator light
Error Tone Cause
RoboVac's left/right wheel is
One beep
stuck.
Two beeps RoboVac's side brush is stuck.
Three beeps RoboVac's suction fan is stuck.
Four beeps RoboVac's rolling brush is stuck.
Wi-Fi Connection
Before Wi-Fi setup, make sure RoboVac and your Wi-Fi network meet the following
requirements.
Wi-Fi Setup Requirements
• RoboVac:
- RoboVac is fully charged and the main power switch on the bottom of RoboVac is
turned on.
- Wi-Fi status light slowly flashes blue.
• Wi-Fi Network:
- Use the correct password for your network.
- Do not use a VPN (Virtual Private Network) or Proxy Server.
- Your Wi-Fi router supports 802.11b/g/n and IPv4 protocol.
- You are using a 2.4GHz router or a dual-band router that is configured to support a
2.4GHz frequency band. RoboVac does not support 5GHz frequency band.
- If RoboVac cannot connect to the Wi-Fi network and you are using a 2.4/5GHz
mixed network, switch to a 2.4GHz network for Wi-Fi setup. You can switch back
once your setup is complete.
- When connecting to a hidden network, make sure you enter the correct network
name, SSID (case sensitive), and connecting to a 2.4GHz wireless network.
28
Solution
• Clean the drop sensors gently
with a dry cloth.
• Place RoboVac in a new location.
• Use a physical barrier to block off
the problem area.
Manually charge RoboVac for at least
5 hours.
Solution
Turn off RoboVac and remove any hair or
debris from the left/right wheel.
Turn off RoboVac and remove any hair or
debris from the side brush.
• Turn off RoboVac, then remove and
empty the dust collector.
• Make sure the suction inlet is not
blocked by any hair or debris.
Turn off RoboVac and remove any hair or
debris from the rolling brush.
- When using a network extender/repeater, make sure the network name (SSID) and
password are the same as your primary network.
- The firewall and port settings of your Wi-Fi router allow RoboVac to connect with
the Eufy servers.
Network Security Requirement
- WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
- WEP EAP (Enterprise Authentication Protocol) is not supported.
Wi-Fi Channels
- The FCC requires that all wireless devices in the United States operate on the 1-11
wireless spectrum channels.
- Some countries outside North America can use spectrum channels higher than
channel 11. Refer to your local regulatory agency to determine which channels are
accessible.
- A future software release will support access to channels above 11 for users outside
North America. Until then, use channels 1-11.
If you cannot control RoboVac with your smartphone, try the solutions below to solve the
problem. If the problem persists, contact the eufy service center for help.
Wi-Fi Status
Cause Solutions
Light
Solid blue RoboVac has connected • Check if your router is connected to the
to your router, but cannot
Internet.
access the Internet.
• Check with your Internet provider to
see if there is any Internet connection
problem.
Rapidly flashing RoboVac cannot connect • Check if you have modified your
blue to your wireless router.
network name and password.
• Reset Wi-Fi connection if necessary.
Refer to the "Use Your RoboVac with
the EufyHome App > Reset the Wi-Fi
connection" section in this manual.
Slowly flashing Wi-Fi connection is reset • Set up Wi-Fi connection with RoboVac.
blue or has not been set up
Refer to the "Use Your RoboVac with
before.
the EufyHome App" section in this
manual.
• Reset Wi-Fi connection if necessary.
Refer to the "Use Your RoboVac with
the EufyHome App > Reset the Wi-Fi
connection" section in this manual.
• RoboVac is turned off. • Charge RoboVac by attaching it to
Off
the Charging Base. Make sure the
• RoboVac's power level
main power switch on the bottom of
is low.
RoboVac is turned on.
• RoboVac is in Sleep
mode.
English
29