Grohe F-digital 36 292 Manual De Instrucciones página 10

Digital controller selection menu
Button Description
Start the selection menu (only if there is no water flowing)
Select by pressing and holding the
• F1 - Automatic filling/safety shut-off
Select other menu items by turning the ring:
• F2 - Calibration
• F3 - Register/de-register additional digital controllers
The selection menu is exited by pressing and holding the
button or automatically after 3 minutes has elapsed.
F1 - Automatic filling/safety shut-off
- Confirm selection by pressing the
Stop the water flow/timer by turning the ring anti-clockwise.
- Start the water flow/timer by turning the ring clockwise.
- / +
- Pressing the
exits the menu.
Abort the menu by pressing and holding the
F2 - Calibration, see Fig. [8]
- Confirm selection by pressing the
- Turn ring anti-clockwise and set minimum flow rate.
=>
Confirm flow rate by pressing the
- Turn ring clockwise and set maximum flow rate.
=>
Confirm flow rate by pressing the
,
- Turn ring measure water temperature and set at 38 °C.
=>
Confirm 38 °C by simultaneously pressing the
Settings are saved and the menu exited.
Abort the menu by pressing and holding the
F3 - Register additional digital controllers
- Confirm selection by pressing the
digital controller simultaneously.
- Press the buttons of the additional digital controller simultaneously
in order to register it.
- / +
- Pressing the
simultaneously saves the selection and exits the menu.
F3 - De-register additional digital controllers
- Confirm selection by pressing the
digital controller simultaneously.
- / +
- Pressing the
simultaneously saves the selection and exits the menu.
Abort the menu by pressing and holding the
Activating continuous operation
With the transceiver, the functional unit can be set to
continuous operation for the purposes of flushing or to perform
a thermal disinfection:
1. The functional unit is off, there is no water flowing and the
digital controller is not in pause mode (wait 30 seconds if
required).
2. Disconnect and reconnect the transceiver's plug-in
connector (C), see fold-out page II, Fig. [5].
3. Wait until the indicator lamp (C2) flashes blue, green
and red, then press the button (C1) within 1 minute.
The indicator lamp flashes blue three times.
7
- / +
buttons simultaneously:
- / +
buttons simultaneously.
buttons simultaneously saves the quantity and
Start/Stop
- / +
buttons simultaneously.
- / +
buttons simultaneously.
- / +
buttons simultaneously.
Start/Stop
- / +
buttons on the existing
buttons on the existing digital controller
- / +
buttons on the existing
buttons on the existing digital controller
Start/Stop
Visualisation
Illuminated ring flashes red 1x
Illuminated ring flashes red 2x
Illuminated ring flashes red 3x
Start/Stop
Illuminated ring flashes violet 1x
Illuminated ring flashes green 1x and water
flow is started
Water flow stops
Water flow starts
Illuminated ring flashes green 3x
Illuminated ring flashes violet 1x
button.
Illuminated ring flashes green 1x and
water flow is started
Illuminated ring flashes green 1x
Illuminated ring flashes green 1x
- / + Illuminated ring flashes green 3x
buttons.
button. Illuminated ring flashes violet 1x
Illuminated ring flashes green 1x
Illuminated ring flashes green 1x
Illuminated ring flashes green 3x
Illuminated ring flashes green 1x
Illuminated ring flashes green 3x
Illuminated ring flashes violet 1x
button.
4. The functional unit is now open for 15 minutes. After
the 15 minutes have elapsed, the indicator lamp (C2)
flashes blue three times.
Caution: Risk of scalding.
Do not stay in the wet area.
Cancel by pressing the button (C1) or any button on the digital
controller, the indicator lamp (C2) flashes blue three times.