Publicidad
Idiomas disponibles
Idiomas disponibles
4.10 Dilations of the sheet. Materials subject to temperature changes undergo dilatations. This phenomenon can cause sporadic
metallic noises more or less frequently. These are completely innocuous and do not mean any risk or problem for its operation.
5. ELECTRICAL INSTALLATION
ALL LOCAL REGULATIONS, INCLUDING THE ONES ACCORDING TO THE NATIONAL OREUROPEAN NORMS MUST BE
ACCOMPLISHED WHEN PROCEEDING TO CONNECT THEA PPARATUS TO ELECTRICAL INSTALLATIONS
5.1. Components. The appliance is equipped with two fans for models Habit 73 TC +T, and with four fans Habit 93 TC +T, a
thermostat and an ignition device, resistance, turbine control switch, inner cables and wires as well as silicon tube for air outlet. For
parts refer to part V of the ANNEXED document.
5.2.1 Electrical diagram with 2 fans.
5.3. Operating. The function of the vent set is to jet the air, once heated, from the lower grill of the apparatus to the front part and the
pipes in the upper part.
5.4. Use and maintenance. The set of ventilation should be permanently connected to the grid when the device is switched on.
The switch offers three positions:
Position 0: Automatic slow gear. The starting and stoppage of the turbines is through the automatic thermostat
-
Position I: Automatic fast gear. The starting and stoppage of the turbines is through the automatic thermostat
-
Position II: Manual fast gear. Manual, not automatic shutdown system.
-
After a period of prolonged and stop before putting the machine in motion, it is necessary to verify the proper operation of the turbines
and cleaned all the dirt of the front grilles of the air intake. It is also desirable that a qualified professional review the entire electrical
installation of the device.
WARNING:
If the feeding wires are damaged, they must be replaced either by sales department or qualified staff to avoid problems.
If an external speed controller is used, switch position I must be selected
6. CLEANING AND MAINTENANCE
6.1 Maintenance. An appropriate and regular maintenance of both the appliance and the installation contributes greatly to its good
performance. It is important to perform periodic and complete controls of the equipment and of the ducts and installation. Thus, for
your safety and comfort, some of our dealers offer a servicing contract for your device. Please contact your dealer for this
service.
6.1.1 Locking mechanisms. You need to make sure no mechanisms are locked (registers, door, air inlet, etc.) after an extended
shutdown period.
6.1.2. Spare parts. Use only original spare parts, or parts recommended by Manufacturas Rocal, S.A. See picture on page 14 of the
ANNEXED document.
6.2. Cleaning. It is important for the appliance to be clean of ash so that all mechanisms work properly. To clean the body of the
device use the cleaning dry cloth given with the appliance or similar. Do not use current cleaning products.
5.2.1 Glass. You must turn the device off to clean the glass. The products used must not come into contact with the metal parts of
the door or the ceramic board; the aggressiveness of these products can cause a corrosion process of the equipment.
6.2.2 Extraction of ashes. Extract the ashes only when the appliance is completely turned off, ensuring that the ashes do not
contain any burning coals; in which case you should deposit them in a metal bucket.
6.2.3. Flue liner. It is important to keep the flue liner clean. It gets dirty depending on the fuel used, on a slower or faster combustion,
etc. You need to clean the flue liner at least once per season. It is mandatory for a specialist to review it periodically. To access the
flue liner follow the steps shown in pictures "D.9", "D.10" and "D.11" of the ANNEXED document.
6.2.4. Painting. The heatproof paint that covers the inside and outside of the appliance withstands temperatures up to 600 °C and
releases a subtle typical smell that disappears after the first few uses.
5.2.2. Electrical diagram with 4 fans.
13
Publicidad
